Toshiba Repair Tips
Search: toshiba
Results: 5617
Results: 5617
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| TOSHIBA |
C7SS
|
Thin hor white line over pic | Move c314 to print side of pcb - see diag in serv briefs | ||
| TOSHIBA |
C7SS
|
Background hiss from rear spkrs | Improved dolby digital module reqd | ||
| TOSHIBA |
C7S
|
Partial field collapse | C323 connected to pin 2 of q501 leaky - 0µ68 50v plastic | ||
| TOSHIBA |
C6SR
|
Pulsing pic & low ht | Q828 in volts control cct leaky - 2sc1815 | ||
| TOSHIBA |
C5SS 3357DB
|
No colour | Qv01 ta1218n (b0385650) | ||
| TOSHIBA |
C5SS 2857DB 3357DB
|
Dead, no led, 12v and 8v supplies ok but 25v missing | Protector z889 5a (23144451) o/c | ||
| TOSHIBA |
C5SS 2857DB 2557DB
|
Pic shifted to rhs, horiz position adj not functioning | 9v regulator q430 not working due to faulty d430 zener mtzj5.1c (23316670) | ||
| TOSHIBA |
C5SS 2857DB 2557DB
|
No volume or channel on screen displays, other menu screens ok | Q501 ta1222an | ||
| TOSHIBA |
C5SS 2857DB 2557DB
|
Dead, no output from psu, fuse ok | D896 byd33j s/c | ||
| TOSHIBA |
C5SS 2857DB
|
Takes long to come on, slight line flicker when changing channels, otherwise blue screen | Replace 27mhz xtal on text pcb (23153472) | ||
| TOSHIBA |
C5SS 2857DB
|
No power, red led on green led flickering | Frame ic ta8427k, r327 (24339479), d302 byd33j | ||
| TOSHIBA |
C5SS 2857DB
|
Distorted sound from cold | Fit 0.1uf cap from base of mute transistor q612 to ground (tosh.technical) | ||
| TOSHIBA |
C5SS 2857DB
|
Bad striations on rhs of the screen | Ensure that line/frame leads are correctly installed in their cable tie clips after working on the set | ||
| TOSHIBA |
C5SS 2557DB
|
No sound from centre speakers | Q604 ta8211ah | ||
| TOSHIBA |
C5SS 2557DB
|
No line or frame sync, osd ok | Q501 tb1226n (b0385673) | ||
| TOSHIBA |
C5
|
Dead - strs6709 keeps going s/c pins 1, 2 & 3 | Also replace d809 mtzj5 - 6b if s/c | ||
| TOSHIBA |
C4E-R
|
Bands of patterning at top & bottom of screen at start up only | Line pulses being picked up by qd03 dpc amp- add 0.001µ cap across rd13 on print side | ||
| TOSHIBA |
C3SS
|
Off | Ic670 audio o/p chip s/c - set in overvolt condition | ||
| TOSHIBA |
C2D 3339DB
|
Tripping, red and green leds flashing at about 3hz | Q828 2sc2230ay leaky (can use 2sc2482 as replacement from onwa crt base) | ||
| TOSHIBA |
C2D 3339DB
|
Hiss/crackle from left speaker | Icg07 ta8776n |