Toshiba Repair Tips
Search: toshiba
Results: 5591
Results: 5591
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| TOSHIBA |
48PJ6DB 55PJ6DB C5SS
|
If power 2 - digicon chassis ( lefthand side from rear ) has been removed , it is possible to swap over the 2 four pin plugs p621 | No damage will be done. ( this is easially done as the shorter lead goes to the far socket ) | ||
| TOSHIBA |
48PJ6DB 55PJ6DB C5SS
|
Convergence errors appear over time , can be adjusted out but re-occur. | Resistors r7716 , r7721 , r7711 ( vertical convergence errors ) or q751 stk392 , r7741 , r7731 , r7736 ( horizontal ) or q752 stk392. all r | ||
| TOSHIBA |
48PJ6DB 55PJ6DB C5SS
|
Bottom of picture blank , clears as set warms up. | Q350 2c1815y leaky. ptno a6317440 | ||
| TOSHIBA |
43VJ13P PROJ TV
|
Int red convergence | Dy joint q753 | ||
| TOSHIBA |
43PJ93B
|
Dead - no st/by led | D7709 6v1 zener s/c on converge panel | ||
| TOSHIBA |
40WH08B C00P
|
St/by only | Check if r821o/c & bridge d802 s/c use repair kit 40whrepkit | ||
| TOSHIBA |
40WH08B
|
When a dark object appears on bright background, overal picture brightness increases, then settles to normal | Wrong option codes. enter design mode and change options bs2, 2bs2, 3bs2, wbs2, nbs2 from 0bh to 07h | ||
| TOSHIBA |
40WH08B
|
Service mode/ design mode | Press mute on r/c once, then press and hold again while pressing menu on front panel. 's' appears on top right corner. to switch to design mode hold call on r/c while pressing menu on tv, 's' on screen should turn to 'd'. | ||
| TOSHIBA |
40PW8DB & 56PW8DB
|
Faint vertical lines on lh side | R441 1k damping res across l441 o/c | ||
| TOSHIBA |
40PW8DB
|
Dull pic when viewed from sides | Dirt on mirror & lens - clean after dismantling | ||
| TOSHIBA |
40PW8 PROJ
|
Int or no pic | Check crt htrs lit - get glue across pin 9 loptx | ||
| TOSHIBA |
40PW03B
|
Protect cct tripping | Q370 bc557 | ||
| TOSHIBA |
378DB
|
No sound, ticking sound | Replace rear speaker amp ic601 | ||
| TOSHIBA |
3787DB
|
Won't go into text mode when operated from sky digital handset | Remote not set properly. each code has a subcode, to enter press tv, then select and red together, then tv again. enter 0156 and press text and tv several times until set goes to text. now press select. | ||
| TOSHIBA |
3787DB
|
Tripping lightly from psu - all o/ps appear ok | C819 22µ 100v low cap | ||
| TOSHIBA |
3787DB
|
Tripping lightly | Q802 coll low (should be 35v) - c819 22µ 100v | ||
| TOSHIBA |
3787DB
|
Tripping - no leds | All volts high - c833 4µ7 or 10µ | ||
| TOSHIBA |
3787DB
|
Tripping - no led illumination | If ht is high c833 4µ7 o/c | ||
| TOSHIBA |
3787DB
|
No sound, ticking in speakers | Ic601 la4282 (23318413) | ||
| TOSHIBA |
3787DB
|
No dolby prologic surround sound | Dj qd01 on the dolby pcb |