Beko Repair Tips
Search: beko
Results: 235
Results: 235
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| BEKO |
14.2
14.2 |
No picture | 1) check and replace c143-100nf 2) check and replace ic101 | Mário Tavares | |
| BEKO |
14.2
14.2 |
P+ is put on the use | Check and replace ic101 | Mário Tavares | |
| BEKO |
14.2
14.2 |
Left speaker sound distorted | Check and replace c326 | Mário Tavares | |
| BEKO |
14.2
14.2 |
After switching on at the first time tsound are lines on the upper part of picture | Check and replace ic501 tda 8359 | Mário Tavares | |
| BEKO |
14.2
14.2 |
Picture is getting bigger and smaller when turning up the sound | Check and replace r606, r607 0.47r | Mário Tavares | |
| BEKO |
14.2
14.2 |
Picture is going and returning frequently | Check r529 1r if tsound is a cold solder or not | Mário Tavares | |
| BEKO |
14.2
14.2 |
Unfocused snowy picture | Check and replace r162-47Ω | Mário Tavares | |
| BEKO |
14.2
14.2 |
No sound | Check and replace c178-4.7 nf | Mário Tavares | |
| BEKO |
14.2
14.2 |
Does not work by remote control | 3) r606-1Ω t601-k2750 kontrol edin | Mário Tavares | |
| BEKO |
14.2
14.2 |
Picture is enlarging and then getting normal. power supply voltages are normal. | Please check bad solder on pins of c519. | Mário Tavares | |
| BEKO |
14.2
14.2 |
Colours disappearing | Please change the c412 connected pin 62 and 63 of ic 101 ( ic tda9563h/n1) from 56 pf to 39 pf and c413 from 33 pf to 39. note : if the colours are still not correct, please insert 47 pf on pos. c412 and 22 pf on pos. c413. | Mário Tavares | |
| BEKO |
14.2
14.2 |
Audio problem | When the unit warms up the sound disappears first, then it stops reacting to the remote control or the frontpanel buttons. picture can still be seen. then you turn power off (mains button) and after you turn it back again, no sound, no reaction to remote and the picture disappears too. check and replace c304 which is connected to pin 24 (reset input) of ic301. | Mário Tavares | |
| BEKO |
12.5
12.5 |
Doesn't work, LED doesn't light | R601-(4,7m) | ||
| BEKO |
CHASSIS 12.7
|
Lack of linearity at the top of the image | Cond. smd c508 (15nf) popped | ||
| BEKO |
CHASSIS 16.1
|
Low voltage on g2 | C712 2.2nf with leakage, this cond. It measures well but under load it causes the symptom | ||
| BEKO |
CHASSIS 16.1
|
Return lines after being connected for about 20 minutes | R709 (220r) in the blanking circuit changed. use components with greater dissipation | ||
| BEKO |
CHASSI 12.7
|
Power power supply. doesn't always start | C610 10nf (smd) with slight leakage | ||
| BEKO |
12220T
|
Dead psu | C110 defective in psu 47uf, 25v - resevoir cap for ic | ||
| BEKO |
PT92
|
E/w failure | Replace cd22 470nf and tv06 bd680 | ||
| BEKO |
PT92
|
High voltage for 5 secs. then goes into protection mode | Replace rv38 2r2 and dd07 by228. check cd22 470nf if o/c |