☰

Beko Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: beko
Results: 235
Make Model Symptom Problem Solution By
BEKO 14.2 
14.2  		No horizontal sync Check and replace ic101 Mário Tavares
BEKO 14.2 
14.2  		There is a bad noise at some channels Check and replace ic101 Mário Tavares
BEKO 14.2 
14.2  		Some channels are absent Replace r129 with 2.5kΩ potentiometer and change the value of c143 as 47n Mário Tavares
BEKO 14.2 
14.2  		Microprocessor spare parts codes in the service manual are not correct Please see tcn's 2003/10, 2003/08 and 2002/17 Mário Tavares
BEKO 14.2 
14.2  		Sometimes flyback lines Replace 220r 1/4w r709 with a stronger one (example 101223). Mário Tavares
BEKO 14.2 
14.2  		Coloured spots on the corners (degaussing problem) Please replace 9r ptc on r602 with two 18r ptc’s (code 154222) in parallel. Mário Tavares
BEKO 14.2 
14.2  		If the unit is in power off state long enough (for example over night) then always when you switch it on, the complete upper part of the picture is messed up and fuzzy. Please check and replace vertical ic, tda8359j on position ic501. Mário Tavares
BEKO 14.2 
14.2  		Is hotel mode available Not available. hotel mode in service mode is for application only. Mário Tavares
BEKO 14.2 
14.2  		No picture Check and replace r162 -47r connected to +8v Mário Tavares
BEKO 14.2 
14.2  		No sound Check and replace c178 - 4.7nf on pin 26 of ic101 Mário Tavares
BEKO 14.2 
14.2  		Defected horizontal transistor bu508df (t504). Check and replace c129 - 2.2nf on pin 11 of ic101 Mário Tavares
BEKO 14.2 
14.2  		Tv can not enter service mode by service remote control With the following software versions onwards, to enter service menu, first activate the “picture menu” with the user remote control and press “9301” (press “0” button to exit the service mode). stereo versions : sb8973-a02, sb8975-a02 (for b,c and d versions will be apllied in time). mono versions : sc3325-a05, sc3325-b07, sc3325-c06, sc3325-d05 Mário Tavares
BEKO 14.2 
14.2  		Protection activated at standby mode Check r529 if there is a cold solder or not Mário Tavares
BEKO 14.2 
14.2  		No teletex Check from service menu whether teletex is open or not Mário Tavares
BEKO 14.2 
14.2  		Picture is indistinct and mat Check and replace r162 Mário Tavares
BEKO 14.2 
14.2  		White lines on picture Check and replace r709 on crt Mário Tavares
BEKO 14.2 
14.2  		Vertical lines on picture Check the solder of dst Mário Tavares
BEKO 14.2 
14.2  		Channels are changing by one selves Check and replace ic101 Mário Tavares
BEKO 14.2 
14.2  		There is a high-pitched noice 1) check and insulate vertikal chock coil 2) check nad varnish l502 coil 3) check dst 4) check l601 Mário Tavares
BEKO 14.2 
14.2  		Tv does not work 1) replace st 601 with 3.15 2) check sw1 3) check c150 mf 400v 4) check ic 101 ; ic 401(24c08); ic 601 (mc44608); t601 k2545; r639 (15Ω); r607 (0.47Ω) ; st601; ph601 Mário Tavares