Cce Repair Tips
Search: cce
Results: 4816
Results: 4816
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
HPS1471
|
Normal sound screen does not light up | Bf421 on tube plate | silva2 | |
| CCE |
HPS 1497
|
No sound | 1 | silva2 | |
| CCE |
HPS 2118USP
|
Tv with side strip | C417 | silva2 | |
| CCE |
HPS-2005
|
Buzzing in the fly-back, excess width and reduction in image height and +b changed to more. | Photo-coupler | FERNANDO S | |
| CCE |
HPS 2001
|
TV turns on all power supplys normally, screen voltage below 250 v filament does not light up | Oscillator just change | Roberto Consertos | |
| CCE |
TV 2118USP
|
Dark band in the left corner of the tube and ripples in the image. | Capacitor polished the 330p more than c417 | I just replaced it and that's it. | charles cbs |
| CCE |
HPS 2910
|
Frame slightly reduced vertically and horizontally, 132v power supply, oscillated, dropped a lot when changing channels | 3k3 / 1k6volts capacitor between the collector and emitter of the horizontal output c 426; thanks jorge barreto sal-ba | Cezar esteves | |
| CCE |
HPS 2997
|
Turn it on and the tube doesn't light up, it only leaves three small spots from the RGB | X 701 12mhz crystal | I replaced it and it was fixed | DIGITÉC ELETRONICA |
| CCE |
TVS2910FS
|
It doesn't turn on, it just stays on standby with a noise tic tic tic very quietly low power supply +b95 and vcc9v | C825 =100uf 160v exhausted | Replace c825 | beto2828 |
| CCE |
HPS2007
|
TV with image and sound but with stripes and the image disappearing | Resistor fr901 on the 22r kinescope board | I replaced it and plz | DELLA FOTOS E CONCERTOS |
| CCE |
HPS2071
34BI |
Flashes standby twice and stops | Fly bak and horizontal exit | ||
| CCE |
HPS1497
|
No secondary power supplys | The TV did not have 103 V or 15 V on the secondary and the LED did not light up. After analyzing the power supply, I found the 18 V dz801 shorted after replacing the zener. it was high, I changed the tl 431 and the photocoupler and replaced the blown capacitor, I monitored the voltages and everything was ok, I turned it on and it worked perfectly | JOSÉ GUSMÃO | |
| CCE |
HPS-2971
|
Image wobbling horizontally and heating the fets at 220v | Abl defect caused by c421 (47kpf/63) in short. (fly-back pin 8) | ||
| CCE |
HPS 1495
|
No colors | Capacitor 0.47mfx50 with failure | Replace the same | nonato |
| CCE |
HPS2991FSC
|
The moment it starts, it comes high and then cuts off | Q805 broken between the base and emitter junction | Replace the same q805 (bc337 npn) | Ademir tc |
| CCE |
HPS2906
|
Increase volume image becomes dark | Alto existed | ||
| CCE |
HPS1471
|
Turns on, just a sneeze on high, turns off | Ver d 408javan | Replace the same | javan |
| CCE |
2197A
|
Stand by access relay activates, then turns off returning to stand bay | I checked the + b and saw that it was correct, after a general check on the board I noticed a capacitor in position c 417 was toast I replaced it and it continued without setting, soon after I found the 180k r414 open and the d 807 shorted I replaced it and nothing then I found the d 813 I replaced it and it finally worked . | Replace c417,r 414,d813,d807 | moroni eletronica |
| CCE |
HPS2007
|
"Sizzling" power supply sounds like frying - in stand by it has 140v and when on it has 103v | Fotoacoplador and there tl431 | Just replace it and it's fixed | NV ELETRONICA |
| CCE |
HPS2171FSH
|
Turns on and then turns off. | Capacitor c825 completely depleted | Replace the c825 for a new 47x160v and hugs! | Paulo Sertel Itararé SP |