Cce Repair Tips
Search: cce
Results: 4822
Results: 4822
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
CCE |
HPS2171
|
Does not turn on relay | Changed screen setting | Lower screen | Fabio |
CCE |
HPS 21AVP
H-2197A |
It doesn't work, but the LED lights up, normal power supply. | Flyback bsc25-0206h shorted | Changing the flyback, but at the moment I didn't have it, I replaced it with the bsc25-0210f, but there was a strip on the right side, so I replaced the 12kv wide c 418 cap with a 15kv one and it worked normally. | jose dacio |
CCE |
HPS2991FS
|
TV turns on, off and on and off, R822 heating up a lot | C740 smd with fault, no use testing | To see if he can eliminate the c740 himself to see if the r822 stops heating, if so and just add another good luck | EVALDO GOMES |
CCE |
29USP OU 2910FS
|
Image shifted from left to right | C402 of 330pfx2kv this one was measuring 50pf, just put a new one and that's it | saulo figueiredo | |
CCE |
HPS-2002
|
Turns on when it wants, stand by LED goes out but does not oscillate | Bad 9v supply | Replace q802, there is no point in measuring, and cold solder the smd resistor that goes to the base of this transistor. | MARCELO QUINELATTO |
CCE |
HPS 21AVP
|
Screen shifted to/right | C-417 proximo ao flay- back , 330pf/ 2kv , azul. | joelton | |
CCE |
HPS1473
|
Does not tune in to any channel | Q-101 bc337 alter in operation | Replace it, even though it looks good in an off-board test | PAULO SERTEL ITARARÉ SP- |
CCE |
2997
2997 |
No sound audio muted | R601 and r 620 100r open | dedesom diogo lopes | |
CCE |
HPS
HPS2997FS |
TV doesn't start, it just stays on stand-by. | Missing 3v3 on the ci eprom tda9873 pin 80 measure all components involving the tranzistor q804: r830,r831,c852,c851, r832, d814 and finally dz808. | If 3v3 is missing, immediately replace the q804, zener dz808 and c851, once the lack of 3v3 is resolved, the TV will trigger the h again. I hope to help someone like you already helped me here hugs | Rodrigo Lopes |
CCE |
1471
|
It didn't turn on and the LED didn't even light up. | I changed the q 804 | edvlado | |
CCE |
HPS 2071
|
It doesn't have 103 volts | Fr802 100r | juci | |
CCE |
HPS 1403
|
+b normal when you press power the LED turns off but does not oscillate | R411 opened or changed | Replacela | antonio nobrega(patos pb) |
CCE |
TV2118USP
|
Image shifted to the right side with aliasing. | C417 changed without measuring | jair cap pitão poço pa. | |
CCE |
HPS2005
|
Has no color | Replace capacitor c501 no pino 36 do multiprocessador | eletronicaae | |
CCE |
HPS 1402B
|
Doesn't work, LED goes out but doesn't give high voltage | Transistor q802 | Replace o transistor q802(bc 337) | |
CCE |
HPS 1497
|
Dead: | R 102 valor de 1 Ω | Marcone | |
CCE |
SS-9900
|
Alternate volume increases and decreases | Cp c810 - remove or exchange | gomes batista | |
CCE |
HPS 2185FS
|
TV turns on, time doesn't turn on | Humidity | I used a hairdryer and waited for the plate to cool down, turned on the TV and it started working again, great. | JOANILDO |
CCE |
HPS-2198 / 21AVP
|
Sometimes it turns on, sometimes it doesn't! I replaced them all bc but the defect continued. Checking the voltage on pin 2 of ic 801, I noticed that it was very low. I followed the line and detected the c806 was leaking. | C806 | DANIEL SOLÂNEA PB | |
CCE |
TV-29UPS
|
With interlaced image | C402 (ceramic head) | Replace the c402 close to the york connection | jarbas santos |