Cce Repair Tips
Search: cce
Results: 4824
Results: 4824
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
HPS-2997FS
|
This TV had problems with the power supply, I corrected the defect and when I turned on the device it took a while for the image to appear and when it did it was an image that was all smudged, blurred, I checked the ABL sector and RGB board and others, I didn't find anything wrong or raised | I got a tip from my colleagues at eletronica2002 that it was just a shot, changing the L400 rf coil or shock for a jampe and then it was steak and fries perfect image and it turns on after about 3 to 4 seconds | Replacing l400 with a jumper is close to the wires that carry tension to the filament | fabiusmax |
| CCE |
TV-2118USP
|
A strange noise in the fly back and a dark stripe on the left side of the tube. | O c417 of 331pf/2kv. | Replace it without testing. | Ademir solânea pb |
| CCE |
TVS2910
|
It takes a while to turn on when it turns on, it takes a minute to turn off | C824 | ||
| CCE |
HPS 2991FS
|
Cp de 100uf.160v | ivo | ||
| CCE |
HPS2185FSG
2185 |
Line horizontally | Vertical defect without +12v | +b12v d402 rectifier diode with small leakage | dedesom diogo lopes |
| CCE |
HPS 2185
? |
It threatens to turn on, but it doesn't turn on, dropping the + b voltage of the power supply. | Flaybk shorted. I changed the flaybk resolvel but it came with a blurred image I checked the abl circuit I didn't find anything wrong I saw the tip from one of my friends here on the forum and I removed l402 that feeds the filament and I put a 1r resistor increasing the voltage from 4volts to 6volts and the image was beautiful! Let's help everyone guys! a hug. | ||
| CCE |
HPS2997FS
|
TV works when image appears brighter - image is flickering | Abl line | R423-1k/1w open | EMERSON RIBEIRO |
| CCE |
HPS21AVP
|
With side stripe separating image | R 418 of 18k open. | Alvanyr |
|
| CCE |
TVS-2910FS
|
Horizontal line | Ver.r407 (15k) c408 (4.7uf/ 250v) c408 (220kpf/250v | kit som sumé-pb | |
| CCE |
HPS-2983
|
Vertical does not open and arming protection | Diode d-410 | Replace without measuring | ELETRONICA NISSEI SOUND embu-sp |
| CCE |
HPS-2983
|
Burning fusistor and vertical output on 51v pin. | Fly back | Replace and resolve | ELETRONICA NISSEI SOUND embu-sp |
| CCE |
HPS2198AV
|
Turns on, then turns off, intermittently | Sw=701,702,703,704,705 | Was replaced | ELETRONICA MEDEIROS |
| CCE |
HPS2071
CHASSIS: 34 BI |
The TV has a normal power supply, the LED lights up, but when you start it the LED flashes repeatedly and the TV does not turn on. | Q403:bc856 pnp completely without any measurement, in the horizontal oscillator circuit a tr smd. | It was replaced and the TV was 100% intact. | Armando de Olímpia |
| CCE |
TODAS COM SAIDA VERTICAL TDA 9302
|
Magnetized type spot in the image | Saida is vertical | ||
| CCE |
HPS2985
|
Doesn't start | C806 in power supply changed | Replace of the same | eletronicaaeb |
| CCE |
HPS-14BSP
RA-104-B |
Red screen with retrace lines | Q901, q903 e q905 | I resoldered the tube plate but it didn't solve the problem, so I decided to swap the Q901, Q903 and Q905 and it started working again. | HEMERSON ELETRONICA MM |
| CCE |
HPS 2081
|
Blinks when changing channels | Q 102 bc547 shorted | HP ELETRONICA | |
| CCE |
1402
|
White image with no command and no characters | Maybe vertical was deficient by these two components | Fr403 of 1r and c421 of 10k | leiroz |
| CCE |
HPS2991FS
|
Does not turn on, no power supplys | 18v zd 801 short | Replace zd801 e ic 801 tea1507p | jasvan souza |
| CCE |
HPS2071
34B1 |
No normal image.sound. all +b test points ok, horizontal vertical oscillator frequencies ok, h output voltage ok, signal l screem ok. | When switching on, inject a 1.5 V signal into terminal No. 6 of the flat to activate the video forcibly; in the case of an image without definition, weakly distorted, change the kinescope. | Replace the kinescope | zak eletronica |