Cce Repair Tips
Search: cce
Results: 4824
Results: 4824
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
HPS-2971
|
Image wobbling horizontally and heating the fets at 220v | Abl defect caused by c421 (47kpf/63) in short. (fly-back pin 8) | ||
| CCE |
HPS 1495
|
No colors | Capacitor 0.47mfx50 with failure | Replace the same | nonato |
| CCE |
HPS2991FSC
|
The moment it starts, it comes high and then cuts off | Q805 broken between the base and emitter junction | Replace the same q805 (bc337 npn) | Ademir tc |
| CCE |
HPS2906
|
Increase volume image becomes dark | Alto existed | ||
| CCE |
HPS1471
|
Turns on, just a sneeze on high, turns off | Ver d 408javan | Replace the same | javan |
| CCE |
2197A
|
Stand by access relay activates, then turns off returning to stand bay | I checked the + b and saw that it was correct, after a general check on the board I noticed a capacitor in position c 417 was toast I replaced it and it continued without setting, soon after I found the 180k r414 open and the d 807 shorted I replaced it and nothing then I found the d 813 I replaced it and it finally worked . | Replace c417,r 414,d813,d807 | moroni eletronica |
| CCE |
HPS2007
|
"Sizzling" power supply sounds like frying - in stand by it has 140v and when on it has 103v | Fotoacoplador and there tl431 | Just replace it and it's fixed | NV ELETRONICA |
| CCE |
HPS2171FSH
|
Turns on and then turns off. | Capacitor c825 completely depleted | Replace the c825 for a new 47x160v and hugs! | Paulo Sertel Itararé SP |
| CCE |
TV2910
|
TV doesn't turn on power supply ok, standbay turns on and off | C402 shorted | C 402 shorted (331x2kv) | VAGNERNARDES |
| CCE |
HPS1471
|
There is no output voltage on the secondary of the power supply transformer | Dz801 | Dz801 replace | fabiano3553 |
| CCE |
HPS21AVP
|
Turning on and off with the standby LED flashing | Change the transistor bc 337 power supply input q802 | DELLA FOTOS E CONCERTOS | |
| CCE |
HPS 2185FS
|
Image blurring in green and blue colors | Trc thomsom, just change | cacereletronica | |
| CCE |
TVS 2910FS
|
When turned on, the image is distorted for 5 seconds and returns to normal after the degausser relay is activated. | Place a 1r resistor parallel to the l400 coil in the filament line near the flyback. there is a variation in this tension. | eletronica fernandes(to) | |
| CCE |
HPS1471
|
LED keeps blinking | Open the screen if the screen turns blue with stripes without osd change tube socket | eletronica karpinski | |
| CCE |
2991
|
TV turns on but there is no video when there is and with symptoms of weak tube | Replace the 2 transistors 337 and cap47x25 and 100x25 before don't forget to check the 10 k resistor | No abl e resistor smd 435 de 4k7 etambem cap do scrim no crt | domingos macedo |
| CCE |
HPS2118
|
TV turns on and then turns off. relay is constantly arming and disarming until it goes into protection | C417, r414, d813 e dz807 | I replaced the components and the TV worked perfectly again. good luck! | DANIEL SOLÂNEA PB |
| CCE |
HPS 1495
|
White lines on the top | C 305 | 47 x 50 v | Roque |
| CCE |
HPS 1495
|
White lines at the top | C 305 | 47 x 50 v | Roque |
| CCE |
HPS 1495
|
Vertical checkered | C 302 | 2,2 x 50v | Roque |
| CCE |
HPS-21AVP
|
This TV pressed the pawer, the relay kept hitting and the LED kept blinking with b+ 117.7 normal @@@ | R414=18k, c417=330pfx2kv,d813 e d407=in4148,dz807=8v2 | Help yourself leave your tip | ELETRONICA ARNI-LEOBERTO LEAL/ SC |