Cce Repair Tips
Search: cce
Results: 4824
Results: 4824
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
HPS2080 B
|
I'm here | Ci 501 tda8361 from line 4x good luck! | EVALDO GOMES ELETRÔNICA GOMES | |
| CCE |
HPS-2780
|
No characters | R-762 open | jacksson | |
| CCE |
HPS 2088
|
It has +b but the LED doesn't light up and doesn't turn on | Replace the 03 bcs transistors: q802, q803, q804. don't test, change! | caio | |
| CCE |
HPS 2991
|
Blurry white spot in the center of the screen | Tda 8359j (saida vertical) | ANTONIO NOBREGA [PATOS.PB] | |
| CCE |
HPS2091
|
Does not activate, sound in st by | Q 401 with leak between collector and base | ELETRÔNICA ESTUDIER | |
| CCE |
HPS1471
|
Doesn't start, doesn't have 3v3 | Pin 66 of ic101 shorted, grounding the 3v3 | Replace ic 101 | jn |
| CCE |
HPS 1497
|
Dead | C-805 of 150uf by 50v, out of stock | When measuring the + b I saw that the voltage was fluctuating and was not stabilizing, then I noticed that it was power so I went and replaced it and the TV worked. | edluz |
| CCE |
HPS2005
|
Lights up on stand-by but does not turn on | Q802 (bc337) dfeituoso | Araujo | |
| CCE HPS2171SF |
HPS2171SF
|
No image | Change the flay and make 3 turns of wire for the filament | ||
| CCE |
HPS-2097
|
TV doesn't work, doesn't come out of standby | Horizontal drive transformer | T401 I removed the transformer and resoldered the pins because I opened it halfway | fabiusmax |
| CCE |
HPS 2990
|
Image with wavy retrace lines, sometimes without color and without audio. | Cold solder on the channel selector, and just joy!!! | Igor Almeida (Eletrônica Igtec) | |
| CCE |
HPS1405
|
Out of tune | Lack of 33v supply (r109 of 2k2 open) | Replacing the resistor | uti eletronica |
| CCE |
HPS 2980 2981
|
Time part time no (or not part) | Ceramic memory capacitor | ||
| CCE |
HPS1470 Q
|
Burning the horizontal output transistor. | Without apparent cause. | Make modification; take a signal diode, in4148 and a 22k resistor for 1/4 of a watt, make a parallel of the two and connect the negative side to ground and the positive to the base of the horizontal output tr... ok. | Armando da Eletrônica só Tv. |
| CCE |
HPS1470 Q
|
TV doesn't program channels, doesn't tune in. | Two diodes and a faulty resistor were detected, d702, d706 and r723. | All items were replaced and it was ok. (note: it was not the microprocessor). | Armando da Eletrônica só Tv. |
| CCE |
HPS 2071
|
Sides closing image varying as if it were a defect in the abl | Ic 801 tea1533 at | Replace ic 801 | ANTONIO NOBREGA [PATOS.PB] |
| CCE |
HPS2071
|
Dead | Chap. power supply duplicator | Replace the same | eletronicaapolo |
| CCE |
HPS 1481
|
Without AV function | Reset on pin 16 of the tda8361 3y de-solder the pin and connect only the pin to ground turn on the TV and turn off this pin was outputting 10 v and conflicting with the q 706 collector | CARLOS AUGUSTO | |
| CCE |
HPS 2997FS
|
TV does not turn on, power supply varying from 80.v to 112v normal 132.5 | Swap d819/d823 | Completed | E. MATOS |
| CCE |
HPS2781D
|
Turns on, but without sound and image. | Check. r410 0.47 10% 0.5 watts. change cap 417 4.7 uf 160v without testing. | MANTENOPOLIS |