Search: cce
Results: 4822
Make Model Symptom Problem Solution By
CCE TVS 2910 FSD
Doesn't start The TV doesn't turn on, nor does the stand by LED light up, just an almost inaudible noise. After checking several components of the power supply I found the r.407 (15k) open and also the d.808 shorted, after exchanging them the TV worked perfectly. As a guarantee I also replaced the q.805 and q.802 (bc337). sebastião
CCE HPS2001
The TV works normally, but it does not have an OSD. Tr q 703=bc547 was found, shorted. It was replaced and the TV was... ok. Armando da Eletrônica só Tv.
CCE HPS-1407
Blurred and distorted image The image was completely twisted and pulled to the side Review fr402 and fr401 This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE HPS2171FSG
Does not turn on, LED is off The LED would not turn on or light up, secondary voltages were zero Dz811 10v, dz801 18v in short and ic801 tea1533at, note this TV shows the +b diagram as 118v but these are 118v It is for a sansung tube if you use a thonson tube the +b is 103v jair.com2008
CCE HPS 2071
On and off vertical closed Replace dz807 8v2 e r824 3r3 robson fabiano
CCE HPS2185
No audio/ add audio Broken audio pll filters Replace C601/C602/C647/C650 Paulo EL. Vakassugui
CCE HPS 2971
No sound in rf There micro If you don't want to replace the IC, remove the jk2 jump, connect a 22k capacitor to the terminal of the IC 669 to pin 29 of the IC 644 and oalaaa ELETRONICA ROBSON(DEBIQUE)
CCE HPS 2990
This TV wouldn't handle the remote control, and you think the defect is in the sensor or the computer. But in fact it only accepts the original control Good luck my companions. This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE HPS 14R
Does not pick up the channels only drizzle and normal voltages 33.5 data and clock varying when changing channels Defective varicap I replaced it and it was fine This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE HPS 14R
Does not oscillate (turns on). normal voltages. it is only on standby. D812 with bad welding on the fly back foot. Tec vídeo
CCE HPS2080D
Vertical closed R 301(1m8) open or altered near the service key alexsts
CCE HPS2002
The TV has 100 volts + b, but it doesn't oscillate, that is, it doesn't start. Analyzing the circuit I found that there was no 9 volts at the emitter of q 802= bc337. So q802=bc337 was replaced, and everything was....ok. Armando da Eletrônica só Tv.
CCE HPS - 2118
It doesn't work, the LED keeps flashing. Fr-401 open.
CCE HPS2780
Burned fountain This power supply burned out due to a broken solder in the yoke connector, I replaced the ci801 q801 which had burned out, I also changed r898, r899, r817, r812, r813 and all the electrolytics and nothing, so analyzing the voltages: I decided to check the resistor r814 connected between the pin 7 and 8 and it was open, replacing it with a new one, the power supply started working normally again. with the defect 1- 3.89 v 2- 0.02 v -> much lower than normal 3- 2.16 v 4- 5.34 v -> much higher than normal 5- 6.40 v 6- earth 7- 2.06 v 8- ​​0.9 v -> much lower than normal 9- 9.27 v without the defect 1- 4.25 v 2- 0.27 v 3- 2.16 v 4- 2.16 v 5 - 6.10 v 6- ground 7- 1.80 v 8- ​​1.82 v 9- 15.4 v This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE HPS 14 RD
Very high power supply, with more or less 150 volts. Power supply regulator, ci str 50103, faulty when turning on the TV there was a loud loud clicking sound on the fly-back pacifier. The str50103 was replaced, the power supply normalized more due to the clicking noises, it also damaged the ci tda 3653b, vertical output then it was... ok. Armando
CCE HPS2780A
Intermittent contrast. Sometimes it would appear normal for a long period and then the level would drop and remain unadjusted (the contrast). I thought the t502 might have a problem and so I connected a wire to its terminals, creating a bridge and the defect persisted. After a lot of work, I removed the t502 and verified that it had an internal capacitor, not included in the diagram. It was the capacitor with intermittent leakage that caused the problem. Disconnect one terminal of the capacitor and that's it! Antonio
CCE HPS2002
Characters missing green Capacitor c717 leaking adelmo elletronica ideal
CCE HPS2002
Characters missing green Leaky smd capacitor, after the change the device started working normally again adelmo eletronica ideal
CCE HPS 1470 OU 2070
Burning str and 120v zener diode Replace fly back roberto consertos
CCE HPS 2988
Fountain pulsing This TV had the power supply pulsing at more or less 120v. the defect was the smd transistor q 806 luismar