Cce Repair Tips
Search: cce
Results: 4816
Results: 4816
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
HPS2904
|
No plot, normal sound | Replace open 100k resistor - r916 | Replace of the same | eletronicaapolo |
| CCE |
HPS2185FS
|
Burning sound output. | Capacitor seco | Replace capacitor..c-645. c-646. c-639. c-641 | gf eletronica |
| CCé |
HPS 29291 FS
N TEM |
Turns on after 2 seconds turns off | Non-secondary power supply transistors | Replace: q804 q802 and 805 and blz | luiztvsom |
| CCE |
HPS-1491 HPS-2091
|
Does not turn on blinking stand by led | Exhausted power supply capacitor | Replacing the c805 power supply capacitor - 180μF / 400 v | JOSEBAURU |
| CCE |
HPS-1402
|
Non-horizontal cut | C423 do pino do video no flay back | Replace it, it has a short circuit | CENTER SOM |
| CCE |
HPS2185FS
|
Completely inoperative (no standby) | After replacing the zener diodes 801(18 volts), 811(10 volts) and the ic 801(tea1533at) and the smd q808(bc846) the TV started working 100% again. | alexss | |
| CCE |
HPS-2070
|
Folded vertical | Capacitor change 100mf pomr 25v | www.esquemarios.com.br | |
| CCE |
HPS-2907 FS
|
Closed horizontal | Capacitor poliester c409 ( 490k ) seco | Just replace the capacitor and the TV is normal | fabiusmax |
| CCE |
HPS-2181
|
Fountain with buzz | R833,r829 aberto | Replacing resistors | |
| CCE |
HPS 2991 FSC
|
Only 2 rectangular bars appear in the center of the screen at the top | The device did not work | Replace the c-409 and that's it. | Conscerta |
| CCE |
HPS 2002 E
|
Horizontal burnout and ultra-fast 819 diode | Switched horizontally and ultra-fast 819 diode | vicena | |
| CCE |
HPS-2091
? |
When it turns on it doesn't work. nothing; After I changed the s.h, I heard a clicking sound (excess mat in the flay tower). | Stop: change of s.h; excess mat=> flay-back exchange | winstontec | |
| CCE |
HPS2997
|
Screen with no image and white lines | 22r/2w resistor on tube plate | I replaced it and it was 0 again | rubens souza |
| CCE |
HPS1403
|
Vertical partially closed, at the bottom it is normal then it forms a bright horizontal streak in the center of the screen from there onwards the image is stretched with the lines very open, you can't see the image! | D301 1n4004 with leak I replaced 1n4007 | GEMASI | |
| CCE |
TVS 2910 FSD
|
Doesn't start | The TV doesn't turn on, nor does the stand by LED light up, just an almost inaudible noise. After checking several components of the power supply I found the r.407 (15k) open and also the d.808 shorted, after exchanging them the TV worked perfectly. As a guarantee I also replaced the q.805 and q.802 (bc337). | sebastião | |
| CCE |
HPS2001
|
The TV works normally, but it does not have an OSD. | Tr q 703=bc547 was found, shorted. | It was replaced and the TV was... ok. | Armando da Eletrônica só Tv. |
| CCE |
HPS-1407
|
Blurred and distorted image | The image was completely twisted and pulled to the side | Review fr402 and fr401 | |
| CCE |
HPS2171FSG
|
Does not turn on, LED is off | The LED would not turn on or light up, secondary voltages were zero | Dz811 10v, dz801 18v in short and ic801 tea1533at, note this TV shows the +b diagram as 118v but these are 118v It is for a sansung tube if you use a thonson tube the +b is 103v | jair.com2008 |
| CCE |
HPS 2071
|
On and off vertical closed | Replace dz807 8v2 e r824 3r3 | robson fabiano | |
| CCE |
HPS2185
|
No audio/ add audio | Broken audio pll filters | Replace C601/C602/C647/C650 | Paulo EL. Vakassugui |