Search: cce
Results: 4822
Make Model Symptom Problem Solution By
CCE HPS2971
TV turns on and off constantly After intense research and replacement of some transistors such as q802, q804, q805 and the TV remained the same I replaced the flybak with the tat2909 and it worked normally. jdmmartins
CCE HPS2007
Does not come out of standby Q802 In the test it is good, I replaced it and it worked perfectly osmar miranda
CCE HPS2007
Has audio and no image Horizontal drive transformer was altered The taf must be less than 100Ω eletronica shalon
CCE HPS-2980
Burns tda4601 (power supply reg.) and also 2sc4430 q80. Resistor r815 (47r) changed. MACC ELETRONICA
CCE 1403
Vertical output heats up and the image becomes blurry Escape in c303 Replace c303 220kpf 100v beto2828
CCE HPS2985
Dead Mosfet q803, q801, and diodes d816, d817 shorted Jaison
CCE HPS1471
34 BI
When turning it on, no image appeared and it turned off When enlarging the screen, a vertical line appeared and it turned off. I checked the +12v and -12v voltages. The +12v voltage only reached 7 or 8 volts and then dropped and reached the q802 emitter, which had a problem. Replaced the q802 0 tv worked odivaldo
CCE A650
000000
Hoarse sound Lack of you n ic301 4558, 308 open it seemed like it was the sound output but it was just r r 308 changer was left filer Replace r 308 15k eletronica marcos melo cascavel ce
CCE HPS-1401 H.
Signals only come in via sky or satellite dish, which appears to be a varicap selector. Ic-101 =diodo zener de 33v,c/ defeito. It was replaced and it was ok. Armando
CCE TV 2991-FS
The TV works and stops successively Transistor q802/q804/q805 altered and capacitor c409 defective Rivaldo Lira
CCE HPS-2991
TV generates without the deflector and with the deflector it generates and cuts. R416 of 820r open. Daniel
CCE HPS 2780
Dark screen and no channel was tuned...sometimes there was distortion in the image. Ok for 33v, vt ranging, agc, la 7910, q-702; The defect was the VCO t-102 coil going to pins 61 and 62 of the la 7685j. thanksuuuuuuu Gutt
CCE HPS 2003
Channels with user lockout and the same "doesn't remember" password Put the TV in st.by mode and press the following sequence on the cr.: p.ch. key (+ 2 seconds), osd key (one touch), mute key (one touch), sleep key (keep pressed until tv to connect). ELETRONICA ESTUDIER
CCE HPS2988
Does not come out of stand-by TV does not come out of stand-by, it was checked, the high power supply +b 135v is ok, which feeds the fly back but it did not generate it. The FBT was changed and the TV worked but with a half screen from the center upwards, vice versa, the cause was resolved by changing the vertical ci tda8359j. good luck if this tip works TODDY
CCE HPS 2901
Upper lines vertically, in the first few minutes then disappear.. Ver c- 424 1000uf x 16v Replace MASTER
CCE HPS1415
It starts with a small band at the bottom of the screen and increases as it heats up. Capacitor c356=1000 for 16v without capacity. It was replaced and it was ok. Armando
CCE HPS1415
Flat screen, no sound, no image and the channel digits do not light up Q101 =bc337 defective. It was replaced and returned to normal. Armando
CCE HPS-2971
Dead Dz801 18v 1/2w
CCE HPS2990
CXA PRCESA
No video Regulador 7805 ic 204 tec.jorge video som caldas
CCE HPS 2997FS
Power supply with 185v when turned on drops to +or- 80v relay knocking R 816 130k precision resistor Joacyr