Cce Repair Tips

Search: cce
Results: 4824

Make	Model	Symptom	Problem	Solution	By
CCE	HPS2990 CXA PRCESA	No video	Regulador 7805 ic 204		tec.jorge video som caldas
CCE	HPS 2997FS	Power supply with 185v when turned on drops to +or- 80v relay knocking	R 816 130k precision resistor		Joacyr
CCE	HPS-2004	When I opened the TV I noticed that the bu was burnt out, I replaced it and when I turned on the TV it didn't take long for the bu to burn again. I was suspicious of everything except the flayback, I even changed the deflection coil but the bu continued to burn.	So that's when I decided to change the flyback.	It didn't burn out, but as a precaution, also replace the horizontal capacitors (772j/1600v.c418, which measures 7.72nonofaraids. and the c416 of 394j/250v, which measures 394nonofaraids.	This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE	HPS-2004	When the TV is turned on, it burns the resistance (fr402) that feeds the tda9309 vertical output. I was not suspicious of the vertical output because the image was open.	But when removing the output I checked pin 5 to 6 of the vertical output was shorted	I replaced the vertical output and the resistance that feeds it and it was fine	This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE	HPS-2004	When turned on atv. it had brightness and sound but no image. Only a lot of lines of retraces appeared, you could even increase the screen until the end and nothing happened.	That's when I checked the resistance in the tube socket (FR901, 22Ω, burnt red, red and black)	It was just a touch and go for a hug	This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE	HPS 2781	The image warps only in some channel.	Factory modification.	Put a 68r and 1/4 watt resistor in parallel with r408=270r and that's it...ok.	Armando
CCE	HPS 2971	Vertical line on screen	Exchange c 409		DEBIQUE
CCE	HPS1403	When you press power, the LED turns off but takes a while to turn on	Replace q802 e dz 807(bc337 e 8v2)		AdrianChapadão
CCE	HPS-2171FS	I replaced the original flayback (bsc25-0206h) with the one that comes with the tat2104 scheme	I just took out the 47kpf c424 and that was it, the image was normal, but it took a while to turn it on and I realized that the filament was very erased.	I put the 47kpf c424 in its place, I took a turn on the flayback ferrite to increase the voltage of the filament, 3volts, the increaser to 4.5volts, it lit up normally and the TV turned on normally without delay, this is because the flayback was not original, but everything was resolved.	fabiusmax
CCE	HPS 2071D 2071	TV turns on with vertical closed with a yellow line and then turns off and on and off	I replaced the q802 and q804, even though they had a good measurement, replace them anyway and put new ones!	These transistors q802 and q804 are responsible for the 3v and 8v supply (volts)	Daniilo20
CCE	HPS-2071	Does not oscillate, rainbow screen appears, colorful vertical lines	Ic301- la78040n		Luir
CCE	HPS1415 ...	Interlaced lines at the top of the screen.	C357=100uf for 35v without capacity.	It was replaced and it was ok.	Armando
CCE	HPS-2171FS	I replaced the original flayback (bsc25-0206h) with the one that comes with the tat2104 scheme	Got a saturated shine	I just took the 47kpf c424 and that was it with a normal image	fabiusmax
CCE	HPS 2901	No weapon,	Change power supply capacitors 100 x 160		ELIZEU RIBEIRO - DF
CCE	HPS2004	Doesn't work at 110 only at 220	Cap 812 47m 63v		rhaus
CCE	HPS-1490	Off the air, in fi, normal in av	After having discarded the varicap, ci 501, capacitors, resistors all from the video part, it was only the ci702pcf8285e-2 (memory). Replacing the problem solved it.		jarbas santos
CCE	HPS2185FS	Standby flashing - when you press power, the relay activates but does not work and the television starts flashing again	Q-802, qd-803 and que-804 with problems, replace them	Leave me This email address is being protected from spambots. You need JavaScript enabled to view it.	Saul
CCE	HPS 2991 FS	Turns on normally, but the screen is black and there is no sound	C901 on the 102k tube board, just change it, good luck		edson gta
CCE	HPS1473 several models	Turn on and off	Q 802 bc327 e q 803 bc337 colocar novo		carlinho bitti
CCE	HPS-144	Protection sometimes works for 1 to 2 minutes and turns off and then turns on	R405 (smd) 3k9 changed to +or- 5k	Just in case, check c 415 6k8 1600v	RTZCOMPUTER