Hitachi Repair Tips
Search: hitachi
Results: 1065
Results: 1065
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| HITACHI |
C2524TZ
|
Loptx replacement | Hr type hr7832 not as in cat - also check r909 39k for hi ht | ||
| HITACHI |
C2524T
|
No sound/pic via scart | Qb01 transistor (bc548) situated behind the socket was leaky. | ||
| HITACHI |
C2524T
|
No sigs | No tuning volts r144 10k, r044 12k o/c | ||
| HITACHI |
C2524R/C2824R
|
Dead - psu blow up | Replace r761, 762, 766 all 2r2, r909, r902, r901, c906, c908, zd903, zd901, zd902, loptr 2sd1884 & chopper tr but12af | ||
| HITACHI |
C2524
|
Dead after width variation & crackling | Replaced r909 39k, q903 but12af, q871 bu508af, c908 4µ7 & kd903. final fault was s/c on tuner 9v line | ||
| HITACHI |
C2524
|
Dead - ht present when psu is unloaded only | R908 39r o/o | ||
| HITACHI |
C2524
|
Cause of psu blow up | Check ht pot | ||
| HITACHI |
C2519T
|
Switches on with max sound | R1555 47r o/c feeds µproc with 5v | ||
| HITACHI |
C2519
|
Slow trip | Tda3654 field o/p chip s/c | ||
| HITACHI |
C2514Z311
|
Hotel mode - stuck in | Hold in vol + and vol- while switch on, when display appears with symbols increase vol to level req | ||
| HITACHI |
C2514TE
|
Weak vid/hiss only in av mode ok in normal | Q005/007 2sc3413 rh of scart skt faulty | ||
| HITACHI |
C2514TE
|
St/by only aft trying to start | Replace ic601 ta8427k c604 100uf/63v o/c and 100uf/63v that is soldered directly to the pins (print side) of ic601.this one was high esr | ||
| HITACHI |
C2514TE
|
Dead - no st/by led | No 5v rail - check r097 82r & q003 bc548 - either 1 or other fitted | ||
| HITACHI |
C2514T
|
Psu blown | R951 82k .5w could be cause of but12af & zd952 s/c & opto coupler ic901 faulty | ||
| HITACHI |
C2514T
|
No picture or sound all controls set to "0" and se | R086 d/d | ||
| HITACHI |
C2514T
|
Int trips into st/by esp on vcr chan | R951 & r953, both 82k 1w - going high | ||
| HITACHI |
C2514T
|
Dead - zd952 p6ke180a zener s/c | R951 82k has gone high in value | ||
| HITACHI |
C2514T
|
Blank raster - all controls at zero | R068 had never been soldered | ||
| HITACHI |
C2509T G7PS
|
Field - bottom cramp | C606 680mfd 16v scan coupling cap | ||
| HITACHI |
C2509T
|
Dead | Replace zd903, q903, q781, c906, 908, 913, 908, 905, 720, rv901. r901, 910, 760, 761, 762, 768. zd903 split in 2 |