Mitsubishi Repair Tips

Search: mitsubishi
Results: 1346

Make	Model	Symptom	Problem	Solution	By
MITSUBISHI	TC1482	Vertical closed	C456 100x35
MITSUBISHI	TC2010	Cold solder on york cable horizontal output shorted and kinescope cut off toasted 10k abl resistor	After replacing the defective components, the image had little contrast, as I checked the abl line and tsound was nothing bad, I concluded that the tool was damaged.	I disconnected pin 10 of the ci, everything was done, the image was normal	Evandro/sousa astel eletonica ceara
MITSUBISHI	TC2054	TV arrived with a burnt vertical ci mpc1488h, I replaced it with a ta 8403k and I also changed the c458 capacitor of 470 mf x 35 volts and the TV was broken	Burnt vertical ci	Electronics technician and installer of c or ku band satellite dishes for any satellite telephone for contacts -33 -30842033	heliomar tecnico em governador valadares 33-30842033
MITSUBISHI	TC 2098	TV turns on normally and turns off in a few minutes and doesn't turn on again	R563 in the open acl line change the same		Francesco eletrônica Gine
MITSUBISHI	TC-1492	Does not light up on stand-by	D 905 short		HP ELETRONICA
MITSUBISHI	TC2099	TV inoperative, stand-by LED blinking	C907 exhausted (22uf/100v)	Replace c907 (22μF/100v)	Denys de Sene
MITSUBISHI	TC 2010	Image without red	CI's video	Replace the same	macedo domingos
MITSUBISHI	TC 2010	Image without red	Replace video ci
MITSUBISHI	TC 2098	Power supply grilling-noise near the traffic	Cond. c907 22x100 replace without testing		kin
MITSUBISHI	TC2098	Q horiz exit. burned. high pulsating power supply from 100 to 200v	Weak capacitors near the regulator.	Replace c905,906.check c551	kin
MITSUBISHI	TC-2099	Image with interference without synchronization	Tda4662, c208,c705	Replace	ELETROCLAUDIOPE AGUAS BELAS
MITSUBISHI	TC-1499 TC-2099 TC-20A	LED lights up and then turns off at high power	R952 changed and c907 with esr changed	I replaced the r952, after that the LED was just blinking, I replaced the c907 and closed the lid	Bruno Capozzoli
MITSUBISHI	TC2098	Snoring in the sound as image varies	Cf301 proximo do varicap	Replace cf301 4.5m	apoloxxx
MITSUBISHI	FP2101	Vertical closed, bright list in the middle of the screen	Ic 101 la76932n 7l		próton eletrônica Avelino lopes,pi
MITSUBISHI	TC2009	On and off.	9 volt regulator.	Replace regulator ic251.	R-TEC Eletrônica
MITSUBISHI	TC-1499 TC-2099 TC-20A	Just measure on a high scale, replace and that's it.	C920 with leak	Just measure on a high scale, replace and that's it.	Bruno Capozzoli
MITSUBISHI	TC-1499 TC-2099 TC-20A	Just turn on the LED	D953 zener 6,8v	Tsound is no point in measuring what measures as good, you have to replace it	Bruno Capozzoli
MITSUBISHI	TC-20	Dull TV, horizontal bands behind the image, remote control accesses the menu, but does not navigate through the options	Horizontal bands, cause: c705 and c703 of 1mf x 50 volts, no brightness, cause: adjustment of the scrim screen and brightness in the TV menu, remote control accesses the menu, but does not navigate the options: tsound are several parallel controls that do not have the function keys	This TV was a gift from a Greek that was donated to me, after years of leaning on it I decided to touch it, when I turned it on, only a light blue screen appeared, I know that this TV has this screen protection when tsound was no signal, I connected it to the antenna, the image appeared, but without brightness , I acted on the screen and it showed an image, but with horizontal bands behind the image, I replaced the c705 and c703 of 1mf x 50 volts which were shorted and resolved, I bought a remote control that accessed everything except navigating the menu to adjust them, so I researched and got tips that said it included the eeprom, I remembered that this TV came with a remote control when I got it, I looked for it... I even thought I repaired it because it was defective, I went into the menu, I adjusted the brightness, color, etc. I re-adjusted the screen and blz, the parallel control did not have function keys to navigate the menu	ivan@
MITSUBISHI	TC-2098	Does not turn on, stand-by LED is off	Short ic901(str-s6707), res.r900/902/905 open, fuse f901 open	Replace them all, check cap.elet.c905/906/907.	jheliocavalcanti
MITSUBISHI	2098	Warming up q901	Change without testing c905 and c906		kin