Mitsubishi Repair Tips

Search: mitsubishi
Results: 1346

Make	Model	Symptom	Problem	Solution	By
TV MITSUBISHI	TC-1418P	Does not come out of standby	When plugged into the socket, the LED turns on normally and then reduces the brightness, that is, it remains on standby, no longer obeying any command.	It was resolved by replacing the horizontal drive transformer.	bf.colatino
TV MITSUBISHI	TC 2018 PS	This TV has a 120v power supply output with 139v. I measured it on the d952, the LED lights up but the TV doesn't turn on and tsound is a hissing sound at the power supply. I've already turned off +b from fly back and it's still the same	Solved this TV. someone (...) placed a coil in place of the 0.22Ω precision resistor. I just removed and inserted a 0.22Ω resistor and the TV worked normally.		bf.colatino
TV MITSUBISHI	TC-2098	It turns out that its sound is normal and tunes the channels perfectly.	I changed the socket/socket and it started working again.		BF.COLATNO
TV MITSUBISHI	TC 1418PS	This television, which according to the customer was connected to the dvd watching a film, during a storm the image on the television in av disappeared, in rf the channels are normal, when activating the av the blue screen appears, if you press menu you have the sound of the dvd nothing but the image	With the change of the ic 101-m52771 asp, the television started working again with av and the normal channels, with colors, but tsound is one but if I connect it to the dvd it stays normal all day long, if I change it to rf it also has the normal channels, if I go back to av the image stays in black and white and the colors only return after it cools down	Resolved by changing the ic-701e101 and eeprom.	BF.COLATNO
MITSUBISHI	CT-21M1 EPM	I didn’t memorize the channels!	After checking the r-955 which was good, the negative voltage of 30 volts was still low, I then verified that the lack of capacity of the c-962 was at the root of the problem, I just had to replace it! these components are located at the power supply power supply next to the transformer.		J.J.
MITSUBISHI	TC2098	Most unsafe part	Shorted image tube		SENPRETOR
MITSUBISHI	TC 1418 PS	It doesn't turn on, it just stays on standby	Trafo 552 open	Replace it or try to recover it	Marcos Antonio Santofofo
MITSUBISHI	TC1499	Does not tune channel	Agc 0,0v	Your 101, replace	SENPRETOR
MITSUBISHI	TC2004ST	Vertical closed	C405 470nf defective (goes to pin 16 of ci 101)	Replacement	CARLU´SAT
MITSUBISHI	TC 2034	Vertical ripples	C-559 = 330 x 10		FERNANDO S
MITSUBISHI	TC 1499	When turning on the TV, a normal image appears, but without color. Then, changing the channel, the color arrives.	C 617 on the run	Replace the same. (Note) wash the plate underneath with thinner using a brush, it helps a lot.	RAIO INFOSERVISE
TV MITSUBISHI	TC 1409 INOPERANTE	Dead	This TV was completely inoperative, with no voltage at all on the secondary transformer. After changing str 6707. I found resistor 954 of 820Ω open and horizontal output bu 2506 dx shorted.	After changing, the TV started working normally again.	BF.COLATINO
MITSUBISHI	TC1410	The power supply was low due to a low of 45v on the STB and 47v max when turned on and the TV did not oscillate even when praying hard.	Ic 951 tl431		RAIOINFORSERVISE
MITSUBISHI	TC-1410	Vertical slightly open with lines at the top of the screen	R462(22r changed) and c467(100nf ceramic) both connected to pin 5 dp ci451.	Replace the r462 and c467	jarbas santos
MITSUBISHI	TC 2009	Slipping away from the tune as if it were a cold sore.	Eeprom memory with data interrupted.	I replaced it and it was fine. A hug and a merry Christmas to everyone	This email address is being protected from spambots. You need JavaScript enabled to view it.
MITSUBISHI	TC 2910	It starts with a small dark band at the top of the screen and after it heats up the band increases until it closes the screen, and tsound is only a horizontal line in the center of the screen.	Capacitor c453=3.300mf por 25v.	It was replaced and it was... ok.	Armando Eletronica Só tv de Olímpia
MITSUBISHI	TC2098	Works for a while and turns off..., all normal voltages...	R 563 ; 180k ,aberto	Trokar ,r563 .180k	dony pinheiro
MITSUBISHI	TC 1499	No horizontal synchronization	Tda 4662		teceletrik
MITSUBISHI	TC-20A	115v power supply measuring 100v and noisy	C902 sold out	Replacement	paulo
MITSUBISHI	TC2099	TV stuck in function lock	You must proceed as follows: with the TV turned off, press the (channel +) key, then press the (channel -) key, the television should turn on normally. however, it will still continue with its active function. To deactivate it, go to the menu and look for the lock function and deactivate it.		heliomar