Philco Repair Tips

Search: philco
Results: 4775

Make	Model	Symptom	Problem	Solution	By
PHILCO	PH14B	No image, removing the signal cable, blue screen appears	Leakage observed between the abl and 180v tracks, causing the resistors r462 of 3k9 and r463 of 3k3 to burn	Note: don't forget to scrape off the carbonization between the trails that leaked	GREIN Eletro
PHILCO	PCM2044	Led lights up but does not oscillate secondary voltage of line plus b with 46	1000\25 c 915 capacitor from the 20 volt line with low capacitance		MACC ELETRONICA
PHILCO	TCM1446	TV with horizontal tilt and no RF signal	C722 470uf16v	I replaced it and everything was ok.	ELETRONICA IDEAL
PHILCO	PCS-2976	Doesn't start	Cold solder d301 next to tda9373ps		ladmyr eletronica universal
PHILCO	PC 1438	It doesn't have 95 volts	Replace str 50103		juci
PHILCO	PCM-1444	Out of tune	L001 on the 9v line. open.	Replace with 1 resistor of 1r x 1w.	Eletrônica Modelo (Jaicós PI)
PHILCO	TV PH 21B	Does not turn on, LED is on but 5v is missing on the v502	C509 220/16 shorted, connected to the v502 emitter	Replace to a 220/25v one	levicordeiro
PHILCO	PCM 1444	Normal operation and after a while it turns off and on several times	Diode in4148 on the run, d301 on the abl line.	Replace d301	MARX MONTE
PHILCO	TP-2010	Stand by on, when the power key is pressed, after a few seconds it flashes.	R930 faulty, change and ok.		Cia do game eletronica - Lapa Pr.
PHILCO	PCS-2076S	Cuts the image and the sound remains black screen with white lines with characters.	Cause: r714 of 4.7r 1/2w and zd801 of 8.2v.	Replace.	Edigar de Souza Moulaz
PHILCO	TP2054	TV doesn't turn on LEDs flashing quickly	D908 inoperative +12v	Replace the memo and everything is ok.	ELETRONICA MONITOR CELSO CAFELANDIA PR
PHILCO	TP20V56	Sem as no rf no of normal	Deprogrammed memory	I did the reset, but then looking at some cold solders on the tube board I noticed that tsound was cold solder on the cable from the PCI to the tube board and then the sound came and went and if I touched the board the sound came back, resoldering resolved it.	HardNet
PHILCO	PT-2053	Setting up protection	When pressing the power button, the LED turned off the TV, it started and oxidized but the filament did not light up, and it remained for about 5 to 8 seconds. and TV ficol ok!	Flyback	Mario teilor
PHILCO	PCS2976, TPS2063-1453-1454		Audio ok, but no sound	Enter service mode and adjust adj, it takes it to 1, and returns to 0.	jasvan souza
PHILCO	TP2054	I'm sound	Eprom		joao bosco
PHILCO BRITANIA	TVPH29US	Several lines on the screen in a vertical direction and a small image fold at the bottom of the screen	C404	Although the capacitance was good, when exchanging it for a new one, the TV was back to normal. The detail in the schematic states that it is 100k, but on the TV it was 1 of 220k, in fact, some components in the vertical area do not match the schematic despite the manual informing the exact model from the TV on the bench.poor thing about the name Philco after it was left to Britannia, things for the users only got worse	JOSÉ GUSMÃO
PHILCO	TP1452/2052	Does not turn on, only stand-by LED is on, normal power supplys, it may also turn off intermittently.	Dz 941 close to flay with leak		ALEX/FETTER
PHILCO	PAVM2920	No high power supply starts with a very strong hiss as if it were a flyback on raw	C725 raw 2200pf for 2kv	Just replace it and that's it	orlando lott
PHILCO	PCM1444,2044,2046 CPH05	Image distorting at the top of the image	R205 does not measure change		GSAELETRONICA PATY DO ALFERES
TV PHILCO	PCS2700	TV has more b and pulsing making a little noise, tick, tick, tick.	Cold solder the resistor r708=47r for 3watts, this resistor is connected to the oscillator drive pin t702.	It was just a matter of resolving it and going out for a hug.	Armando de Olimpia Eletronica EvoluSom.