☰

Philco Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philco
Results: 4775
Make Model Symptom Problem Solution By
PHILCO TV PH 29B
TV turns on normally and then turns off, flashes stand by Lack of voltage on pin 28 of ic 201 D 408 shorted, just replace, near the fly back controls albertpir
PHILCO PCS-2956
With retrace line and variation in width Capacitance,c728/3n3 1k6 Direct replace c728
PHILCO TPF 2902
Sides closed about 10 cm works for seconds and turns off Capacitor c 706 6n8/1k6 Replace c 706 celito santo angelo
PHILCO TPF-2121
High power supply +b was 154 volts R 919=120k eletronica universal
PHILCO TP1453
TP1463 		Takes time to turn on +b 123v when changing channel it turns off R919 amended Replace tonico
PHILCO TP29C21
Horizontal shifted to the right,(normal time, shifted time); taking up to 2 days. Cap.smd (c705) on pin 16 of ic101 was cold soldered. I tested it like this! , (place cap. (the defect disappears)) when (remove cap. (the defect appears)). Alextecnico
PHILCO TPF2121
TV only on standby, when turned on the LED blinks After checking all the voltages and horizontal line, capacitors, horizontal output, flayback everything was ok, I then checked the 6n8 horizontal output capacitor, it had a capacitance of 3n2, just change it and run for hug C715 capacitor replaced Felipe
PHILCO PCM1444
CPH05 		Line standing almost in the middle of the screen, when it heats up it disappears. A rabble Remove the glue that remains on top of it and clean the area with isopropyl alcohol. hndrsn
PHILCO TV PH21B
Vertical fully closed even after changing la78040b Measure the power supply if it is below 20v, clean the glue from the VD564 and VD566 diodes Take the diodes out and clean the glue if possible, clean the area with thinner antonio nobrega(patos pb)
PHILCO TV PH21B
Vertical fully closed even after changing la78040b Measure the power supply if it is below 20v, clean the glue from the VD564 and VD566 diodes Take the diodes out and clean the glue if possible, clean the area with thinner antonio nobrega(patos pb)
PHILCO TV PH29
Doesn't start Power supply burning the strw6556a and primary diodes and fuse. I put the strw6556a in and it burned again, when I turned on the TV with the 150w lamp in series then the TV didn't burn the strw and showed smoke coming out of the replaced c-553 (471/1kv), changing the c-553 tv went back to work perfectly. Adilson(formiga-mg)
PHILCO HITACHI PC1438UO1436
CH04 		Tuning goes out when turned on when it heats up normal account Defect abias amorim silva
PHILCO HITACHI PC1438
CH04 		Tuning goes out when it turns on when it gets hot it returns to normal Defective tv abias amorim silva
PHILCO PCS 2956
When I turned it on, it turned on and at the same time turned off, that's when I realized it was entering the protection system I removed the, q707 and it fused again bonzinho
PHILCO PCR2049
Has sound and no image with character Cause: shorted 801 diode
PHILCO PCS-3320V
Cup effect (rounded black line at the corners of the screen) R-722-100Ω Replace and go for the hug samuel leite
PHILCO PCS-3320V
Burning horizontal outlet Fly back (ffa97017l(1) ou ffa97035l) e d707(by222) I just had to replace them and the defect was resolved. samuel leite
PHILCO PCM2046
It turned on and off without stopping with loud flashes and pops. R715 of 4.7onhs open alvaro
PHILCO PCM2046
After 10 minutes switched on, it disarmed with a low whistle D302 with leaks code;1n4148 after the replace tsound was no more disarming, it was fine.
PHILCO TP2053
Dark screen in a few moments turns off and flashes stand by Poor contact on the cable that transports RGB to the kinescope, resolder the vertical output. guaracy borges