Philco Repair Tips
Search: philco
Results: 4811
Results: 4811
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
PCM-1444
PCM-1446
PCM-2044
PCM-2046
CPH05 |
Red screen not blue screen | Ic memory | Memo | toninho da eletronica |
| PHILCO |
PCS-2076S
|
The screen goes black with three lines of green, blue, red and sound. | R708 check the 45v fly back. | Replace this tip works for maxvision, platinum, emotion too. | Edigar de Souza Moulaz |
| PHILCO |
PC20R42
|
Entered into protection, only turns on if unplugged | Defective deflector coil | Replacement | Eliel Magno |
| PHILCO |
PCM1444 PCM1446 PCM2044 PCM2046
|
Alloy with retrace lines on the screen, loud speaker emits a light on the flech-like screen | Capacitor c719 10mfx250v | C719 10μF x 250v | toninho da eletronica |
| PHILCO |
TP-1452N
|
Without tuning channels (completely off air) | Mf201(next to the video ci) | Replace the same | Jarbas (ELETRO-SERV) |
| PHILCO |
PE14H
|
With low supply +-20v on b+ | Q881 leaking. | Replaced by bf422, pay attention to collector and emitter. | eletronicaoeste |
| PHILCO |
TV PH21C
|
Does not turn on, LED keeps flashing, +b with 20v | Q881 2n5551 | ||
| PHILCO |
TP2010
|
Lines at the top of the screen and rainbow effect. | Replacement of ic601 (tda8177) | Replace the c.i. The equivalent or replacement tda is tda9302. | R-TEC Eletrônica |
| PHILCO |
PH 14D
|
Stand by LED does not come out blinking | Q881 / r882 / r881a / c883 / c882 | Replace q881 2n5551 por mps-a42 / r882 - 22k / r881 - 10r / c883 - 470/25 / c882 470/25 | eletronicaapolo |
| PHILCO |
PH 21 SS
|
Dark canvas about 10 centimeters at the bottom, top part of the retrace lines | I changed the 24c08 eeprom and it was just luxury!!! | Ray Ferreira | |
| PHILCO |
DV-P4800
|
No image on normal output, just scrambled image on component video output | Memory 24c02 | Changing it doesn't even need to be recorded | ELETRONICA GAZZIN - felipe |
| PHILCO |
TP 2053
|
Turns on and off and flashes stand by | R 919 secondary power supply (must be changed) | ||
| PHILCO |
TPF 2902
|
Expanded image, and like a slight cushion defect. | The 6.8uf c707 electrolytic was replaced for 47 uf, close to horizontal. | Leandro | |
| PHILCO |
PC2041
|
No image with sound | C301 0,47mf | Replace | juci |
| PHILCO |
PCS-2976
|
Just turning off, the LED blinks and only turns on after taking it out and plugging it into the socket. | Power supply regulator q901 11n60 faulty | Replace q901 without measuring | eletrônica reis |
| PHILCO |
PH29US
|
Philco TV closed from the middle down | Faulty memory | Replace without wasting time for a new one, it can be 24c16 or 24c08 | Sergio |
| PHILCO |
PCS-2952
|
It doesn't start, STBY LED flashing, +b voltage [120v] only drops about 12 to 15 volts. | C949 [220uf/ 200v] seco. | Replaced for a 470μF/200v one without any replaces. | Altevirlima_Valparaiso Eletrônica_PA |
| PHILCO |
PH 21 E
|
Tall and short | Diodo zener 5v6 (d805) | oilec | |
| PHILCO |
TP2054
|
When trying to turn on the power supply it would be normal, then it would go down and tsound would be a noise from the speakers. | Transformador driver horizontal t702. | @gepe | |
| PHILCO |
TP-2920
|
TV does not turn on (inoperative) TV in stand by When turned on, the LED flashes and the power supply does not start, remaining in stand by. | The polyester capacitors 1701 and 1703, both 6n8/1600v, which are located in the TV's primary power supply, were replaced. | MAGDAEL |