Sony Repair Tips
Search: sony
Results: 20092
Results: 20092
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
EXR14
|
No audio/display (found d705 shorted) | When turned on, unit had no display and would have audio forabout 3 seconds only. found d705 shorted, keeping vdd from ic701. | ||
| SONY |
EXR10
|
No power to tape deck (found r361 and r362 defective) | The motor had no power. found r361, r362 reading well overtheir normal 6.2Ω value. | ||
| SONY |
CDXU8000
|
15p flex connector torn | Both cables torn in same spot. samples forwarded. cable is being torn by shield on main board. i have not seen this shield on other models using this mech. | ||
| SONY |
CDX5270
|
No tuner audio or seek (found ic503 defective) | No tuner audio - tuner wouldn't seek, would only increment.stereo always displayed. cd functions and audio ok. | ||
| SONY |
CDX5260
|
Won't load, makes clicking noise | Will not take cd's makes loud clicking noises. | ||
| SONY |
CDX5260
|
Starts play but doesn't continue (repaired traces on md mcb) | Cd goes into play, plays for 3-5 seconds. cd mech/fop emitsfaint squealing noise as though sled circuit is starting to track. uniteventually reads code e0-4. | ||
| SONY |
CDX5070
|
Tuner audio cuts out and in (found poor solder on fe601) | The tuner audio would cut out and in, cd audio was o.k. | ||
| SONY |
CDX5060
|
Would not accept disc (d804 was missing from sensor board) | Unit would not accept disc. | ||
| SONY |
CDX5060
|
No power (found metal tab of chassis shorted to display pcb) | Unit would not power up no display, tuner, or cd operation. | ||
| SONY |
CDX5060
|
No power (found r536 open) | Unit had no power. | ||
| SONY |
CDX5060
|
Intermittent audio output (found d516 installed backwards) | After a few minutes of operation, audio would mute on its owna little whle longer it would come back on. i found that d516 had beeninstalled backwards at the factory. | ||
| SONY |
CDX45RF
|
Intermittent display (re-soldered j4 on hideaway board) | Display would intermittently go blank. found broken solderjoints on hideaway pcb at commander input jack. | ||
| SONY |
CDX45
|
Disc remains in unit when magazine is ejected | A disc remained in the mechanism when the magazine wasejected. | ||
| SONY |
CDX45
|
Won't load discs (found chucking plate bracket bent) | Would not load discs. discs would hit chuck plate like oldermodels. | ||
| SONY |
CDC5070
|
Cracked foil on main pc board | Foil crack on top side of board. it starts at heat sink (12)for q520 and runs by q503. i have seen 3 units with this problem. | ||
| SONY |
HVA441
|
D601, d602, d603, d604 wrong part number listed. | Part number listed as: 8-719-906-39 is wrong. should be8-719-300-33. | ||
| SONY |
CCDVX3
|
Top of picture distorted unit vibrates/replace drum | Picture was distorted. replaced drum. problem became worse.replaced supply reel and back tension band. still a problem. took notethat unit had a vibration in play. | ||
| SONY |
CCDVX3
|
Zoom stuck - open unit, npf/ see sb csv-3 #335 | I have several units 34, 17534, 08, 17826, 44, 59856, and now12, 47526. the flex cable gets dimples in it from cr 42 board c046 andarea. the flex cable is nbo and the customers tend to get irate. 12,47526 says rush on it. | ||
| SONY |
CCDVX3
|
Unable to perform back flange adj. | Technician attempted to perform the back flange adjustment.tried several times but unit would lock up before completing adjustment. | ||
| SONY |
CCDV99
|
Speed changes from sp to lp during scan (c837) | Refer to fpr o3609. although replacing c833 effects a cure,additionaly replacing c837 further reduces the noise and enhances the longterm performance of this unit. |