Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
SLVR5UC
|
Smeary red on self-recordings: adj rv302, rv303 on yc93 bd | Customer complained of smeary color on some tapes. svcr wasonly able to see problem on self-recorded tapes, pre-recorded movies wereok. noticed that lipstick on faces was displaced to the right. | ||
| SONY |
CCDTR31
|
No chroma from camera/check q706, vc12 board | Camera had no chroma just b/w picture. also noticed tapeplayback had chroma interference lines but had chroma. q706 on the vc-122board was not soldered into place. | ||
| SONY |
CCDF77
|
Will not load tapes/check pin 12 ic503 ss100 | Would not load tape and trouble indicator came on. found novcc at pin 12 of ic503. feed through was open near c513- vcc line. | ||
| SONY |
CCDFX410
|
No video/replace timing generator ic 801 | Unit had no ee video. found trash on v1 to imager ic. | ||
| SONY |
CCDTR200
|
No auto or manual focus/replace lens assy | Unit had no auto or manual focus. | ||
| SONY |
DTC87ES
|
Intermittent static in audio - cn351 improperly seated | When playing back or recording analog, the meters were pegged. | ||
| SONY |
ACV25
|
Intermittent operation q101/ma146bd | Unit will power up with battery for 5 minutes and the powerled goes out. | ||
| SONY |
LANCJIG
|
Does not autotime with a 486 55mhz or 66 mhz computer/techrp | The auotiming does not function properly with a 486 55mhz or66 mhz computer. -hq comments: this problem has not been verified at this time. in theevent that this should happen, have your technical representative contactheadquarters for a possible solut | ||
| SONY |
LANCJIG
|
Port 4 does not operate; jumper ic5 pin6 to near side of r7 | Port 4 of the jig does not operate, all other ports are ok | ||
| SONY |
DTC59ES
|
Intermittent noise in left channel (ee mode) | Intermittent noise from left channel in ee mode. did nothave another unit to play back tape on, so don't know if noise wasrecorded. | ||
| SONY |
FDLK400
|
No pix, no sound with brightness switch on anything but low | Noticed that the display would go to a blue screen when anysetting other than low on the backlight brightness switch was used. | ||
| SONY |
TCDD3
|
Noise in audio (replace capstan motor, p/n 8-835-412-01) | Audio would intermittently have digital noise. rf waveformshowed occasional breathing. all electronics appeared ok. | ||
| SONY |
CCDTR7
|
No auto focus or manual zoom/replace ic613 vc80 board | Unit would not auto focus and manual zoom was not working.when the camera was on, the zoom motor would run continually without anybuttons being pushed. also, the motor would not respond to the zoomcontrols. | ||
| SONY |
KV27XBR26
|
No picture no sound hv ok, replaced ic1002 on "u" board | No picture. no sound. high voltage ok, but just horizontalline. | ||
| SONY |
KV27TS36
|
Buzzing noise, glued t601 line filter | Buzzing noise coming from back of set, when the tv is on or off. the tech applied hot glue to the transformer, (line filter) stoppingthe buzzing. | ||
| SONY |
KV2182P
|
V out substitution upc1498h, pin 8 is not used | The original vertical output is a upc1488h which is a 7 pinic. the replacement is a upc1498h which is a 9 pin ic. how is the ic tobe configured? we cannot seem to find any information. i did check withkirk vistain. | ||
| SONY |
KV13TR28
|
No horz./high voltage, r341 open on "a" board | Unit had no horiz/high voltage. power supplies were normaland jungle ic had 9v. voltages checked pretty close if not correct.(pin 37) was 1.8v instead of 2.7v. found pin 43 (8v) read 7.9v and pin42 read 3v instead of 4v. | ||
| SONY |
CDX5260
|
Explanation of error codes not shown in service manual | Is there a list of the error codes available for the abovemodel? how about other models? -hq comments: the list of error codes for this model is limited, andunfortunately the explanations are not very descriptive. the only errorcodes we know about ar | ||
| SONY |
CCDFX510
|
Ordered (arm t) assy, guide received (arm s)assy guide | Upon repair of ccdfx510 r#209 is needed. but i receivedr#230 in parts bag. so, i ordered both parts x39412671 and x39412661 andreceived r#209 in both bags. enclosed are the unopened bags. -hq comments: kansas city checked their stock and fixed the p | ||
| SONY |
SLVR5UC
|
No video out to monitor and rf outputs: l861 on cg-10 bd. | No video through monitor out, also no video signal for rfmodulator. |