Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
KV32SXR10
|
Dark picture, resoldered dl302 | Picture becomes dark and red intermittently. during the lastsix months, i saw several cases like this. it also occurs on the kv25xbr. -solder: after resoldering dl302, the set worked fine. -hq comments: the y signal is supplied from the delay line dl30 | ||
| SONY |
ITB3
|
No audio from handset speaker - resolder speaker wires | No audio out of handset. opened handset and found connectionson speaker had never been soldered at the factory. the wires werestripped back and put through the holes on the speaker, but no solder hadever been applied to the connections - no even a trac | ||
| SONY |
CCDFX310
|
Wrong left cabinet assembly order | Ordered left cabinet assembly for ccdfx310 which is gray incolor and received a black left cabinet assembly. are the part numbersin the manual for the fx310 and fx311 switched? | ||
| SONY |
SLV595HF
|
No fluorescent display: r215, r216, r207 sr370 board | No display, but the unit would operate. | ||
| SONY |
CCDTR200
|
Washer removal tool | After only a few uses, the tip of the removal tool broke off.is there a reliability problem with this part? -hq comments: so far, we have not had a reliabilty problem with thistool. however, the tip part of the tool is very delicate. we will monitorthe | ||
| SONY |
TADL100
|
No audio - ic109 faulty 8-759-604-29 | No audio output. rf is not transferred from tadm1000 totadl100. | ||
| SONY |
TADL100
|
No control from remote room - cold solder on cns701 | No functions, keeps blinking, and does not accept commandsfrom the system. | ||
| SONY |
KV32XBR95S
|
Vertical distortion, replaced ic1501 (vert output ic) | Transparent horizontal line through the middle of thepicture, with small amount of fold over at the top of the screen. theproblem occurred after 10 minutes. applying freeze spray to the verticaloutput ic1501, would cause the problem to disappear. | ||
| SONY |
CCDF501
|
No mech functions/replace ps501 | Found ps501 open. | ||
| SONY |
GDM2036S
|
Picture stretches vertically due to ic-201 | After warm up, the picture will start to stretch vertically atthe bottom. customers says it would take anywhere from 1/2 to 2 hours.by heating and cooling ic-201 i was able to produce the problem. | ||
| SONY |
SLHF840D
|
Tape partially loads then ejects: capstan motor | When the tape is inserted, it partially loads then ejects. | ||
| SONY |
KV27TS29
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote (rm-y116) does not beep. is theowners manual correct or not?hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is com | ||
| SONY |
KV20V50
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote (rm-y117) does not beep. is theowners manual correct or not?hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is com | ||
| SONY |
KV27TS32
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote (rm-y117) does not beep. is theowners manual correct or not?hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is com | ||
| SONY |
CDPC235
|
No optical pickup functions (resolder cn101 and cn102) | Laser of cdp-c235 would not turn on, no focus, and opticinoperable. there was no +5v on pin 7 of cn101 or pin 5 of cn102. | ||
| SONY |
KV32TS46
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote (rm-y118) does not beep. is theowners manual correct or not? hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is co | ||
| SONY |
KV32TW78
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote (rm-y118) does not beep. is theowners manual correct or not? hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is co | ||
| SONY |
KV32TW77
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote (rm-y118) does not beep. is theowners manual correct or not? hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is co | ||
| SONY |
KV27TW78
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote (rm-y118) does not beep. is theowners manual correct or not? hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is co | ||
| SONY |
KV27TW77
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote (rm-y118) does not beep. is theowners manual correct or not? hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is co |