Sony Repair Tips
Search: sony
Results: 20077
Results: 20077
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
SLV595HF
|
No fluorescent display: r215, r216, r207 sr370 board | No display, but the unit would operate. | ||
| SONY |
CCDTR200
|
Washer removal tool | After only a few uses, the tip of the removal tool broke off.is there a reliability problem with this part? -hq comments: so far, we have not had a reliabilty problem with thistool. however, the tip part of the tool is very delicate. we will monitorthe | ||
| SONY |
TADL100
|
No audio - ic109 faulty 8-759-604-29 | No audio output. rf is not transferred from tadm1000 totadl100. | ||
| SONY |
TADL100
|
No control from remote room - cold solder on cns701 | No functions, keeps blinking, and does not accept commandsfrom the system. | ||
| SONY |
KV32XBR95S
|
Vertical distortion, replaced ic1501 (vert output ic) | Transparent horizontal line through the middle of thepicture, with small amount of fold over at the top of the screen. theproblem occurred after 10 minutes. applying freeze spray to the verticaloutput ic1501, would cause the problem to disappear. | ||
| SONY |
CCDF501
|
No mech functions/replace ps501 | Found ps501 open. | ||
| SONY |
GDM2036S
|
Picture stretches vertically due to ic-201 | After warm up, the picture will start to stretch vertically atthe bottom. customers says it would take anywhere from 1/2 to 2 hours.by heating and cooling ic-201 i was able to produce the problem. | ||
| SONY |
SLHF840D
|
Tape partially loads then ejects: capstan motor | When the tape is inserted, it partially loads then ejects. | ||
| SONY |
KV27TS29
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote (rm-y116) does not beep. is theowners manual correct or not?hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is com | ||
| SONY |
KV20V50
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote (rm-y117) does not beep. is theowners manual correct or not?hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is com | ||
| SONY |
KV27TS32
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote (rm-y117) does not beep. is theowners manual correct or not?hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is com | ||
| SONY |
CDPC235
|
No optical pickup functions (resolder cn101 and cn102) | Laser of cdp-c235 would not turn on, no focus, and opticinoperable. there was no +5v on pin 7 of cn101 or pin 5 of cn102. | ||
| SONY |
KV32TS46
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote (rm-y118) does not beep. is theowners manual correct or not? hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is co | ||
| SONY |
KV32TW78
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote (rm-y118) does not beep. is theowners manual correct or not? hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is co | ||
| SONY |
KV32TW77
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote (rm-y118) does not beep. is theowners manual correct or not? hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is co | ||
| SONY |
KV27TW78
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote (rm-y118) does not beep. is theowners manual correct or not? hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is co | ||
| SONY |
KV27TW77
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote (rm-y118) does not beep. is theowners manual correct or not? hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is co | ||
| SONY |
KV32TS36
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote (rm-y118) does not beep. is theowners manual correct or not? hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is co | ||
| SONY |
KV27TS36
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote (rm-y118) does not beep. is theowners manual correct or not? hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is co | ||
| SONY |
RMY118
|
No beep sound when using code set function, normal | Owners manual states a long beep sounds, indicating that thecode has been set. customers remote does not beep. is the owners manualcorrect or not? hq comments: the owners manual is incorrect. no beep sound will be heardwhen the code set is completed. |