Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CPD1304
|
No picture | When using the vga wonder card (1056 x 350) in the inhancemode, picture will blank out. -hq comments: vga wonder card drops below 28khz. this models specs willnot go below 28khz. | ||
| SONY |
SLHF360
|
Tape threads half way then ejects - reel table will not turn | Tape threads half way then ejects. reel table will not turn. | ||
| SONY |
KV27XBR10
|
Raster, no video, loss of h sync, replaced ic-531 | Screen displayed raster, no video, severe loss of horizontalsync and severe pincushion distortion. waveform check revealed no signalat pin 1, ic-531. resistance check revealed 200Ω short between pins1 and 7 of ic-531. horizontal frequency was also | ||
| SONY |
DT4
|
No laser in new optical device | There is no laser in a new optical pick-up device. pin 9 andpin 8 are shorted in factory. all new fop (optical pick-up devices) havethe same problem. | ||
| SONY |
D2
|
No laser in new optical device | There is no laser in a new optical pick-up device. pin 9 andpin 8 are shorted in factory. all new fop (optical pick-up devices) havethe same problem. | ||
| SONY |
D4
|
No laser in new optical device | There is no laser in a new optical pick-up device. pin 9 andpin 8 are shorted in factory. all new fop (optical pick-up devices) havethe same problem. | ||
| SONY |
CCDV2
|
F-902 keeps blowing | Iris stays closed, unit shuts down after a few seconds incamera mode only. f-902 keeps blowing. | ||
| SONY |
CCDTR5
|
Missing part number step up ring/ 3-707-568-01 | Part number is missing for the step-up ring from 37mm to 40mm. -hq comments: the part number is 3-707-568-01. | ||
| SONY |
CCDTR5
|
Only zooms one way | Unit only zooms one way. | ||
| SONY |
CCDTR5
|
Dead unit | Unit came in dead. | ||
| SONY |
CCDTR5
|
Camera section dead | Camera section dead, vtr is ok. | ||
| SONY |
CCDTR5
|
Eats tapes | Unit eats tape. they were catching on the take up reel. | ||
| SONY |
CCDV99
|
Picture blanks briefly during insert edit | When an insert edit is done through the composite video inputs(not hi8) onto a tape with hi8 recording, a problem occurs on playback onthe inserted portion. at the edit points there is a glitch where the pic-ture blanks quickly. the edit is not a clean | ||
| SONY |
TCRX400
|
Pcb layout differences | Pcbs differ in these two tape decks. both pcbs differ fromthe layout in s/m. is there a s/m supplement? -hq comments: there are no supplements published. i will ask tokyofor information on changes and respond to you. there is an extra jumperground | ||
| SONY |
MDP700
|
Lines in video | Noise lines in video while playing, but not in pause or stopmodes visible in color or black and white pictures. | ||
| SONY |
CDP200
|
Replacement of ic-602 | New ic does not work. | ||
| SONY |
CDP101
|
Replacement of ic-602 | New ic does not work. | ||
| SONY |
CDP701
|
Replacement of ic-602 | New ic does not work. | ||
| SONY |
CDP400
|
Replacement of ic-602 | New ic does not work. | ||
| SONY |
KV27XBR10
|
No power up from front panel, found d-106 in place of c-115 | Unit would not power up from front panel - all other functionsokay. |