Sony Repair Tips
Search: sony
Results: 20073
Results: 20073
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
D4
|
Intermittent no power | Unit does not turn on - but turns on when upper lid is pusheddown. the open leaf switch (s-801) does not contact well because the openleaf switch is bent or the pushing lever in the upper lid is worn out. | ||
| SONY |
D15
|
No spin/scraping noise during play | The height of the turntable is too low. it should be 1.5mm or2mm from md chassis. a disc does not spin because there is no gap betweenthe turntable and md chassis or the gap between them is just too small. adisc touches the md chassis intermittently. | ||
| SONY |
MDP200
|
Radio frequency interference | Unit had herringbone type interference caused by a.m. radiostation 850 k.c. whdh needham, massachusetts (approximately 1 1/2 milesaway). problem showed up in both video and r.f. out. the interference isa.c. line related. | ||
| SONY |
GEN-CAM
|
8mm lapping tape | What is the part number for the 8mm lapping tape? -hq comments: the part number for the 8mm lapping tape is 8-883-103-10. | ||
| SONY |
WMF100II
|
Tape will not play or excessive wow and flutter | Pinch roller touches part of cassette shell causing excessivewow and flutter or no play. | ||
| SONY |
STRAV900
|
Part number needed - insulating mica | Is there a part number for the insulating mica for the outputtransistors (2sc3856 and 2sa1492)? -hq comments: the mica insulators are shown on page 29 of the servicemanual as reference number 57. part number is also listed it is4-885-901-31. | ||
| SONY |
EVS700U
|
Lp mode playback picture is distorted with self-recording | Sp mode is ok. when i recorded and played it back in lp mode,one channel of ri waveform level is too small. | ||
| SONY |
CCDF40
|
Wrong part number for dt-71 board in manual | When servicer orders part number a-7061-127-a as in the manualfor the (dt-71) board, he receives an (aw-10p board). -hq comments: please change the service manual to the correct partnumber which is a-7068-127-a. | ||
| SONY |
SLV555UC
|
Transistor type correction | Transistor q-102 is drawn as a pnp transistor on page 83 ofthe service manual. | ||
| SONY |
CCDV3
|
Ccd-v3 lens hood | Is there a repair kit for the ccd-v3 lens hood? -hq comments: no there is no repair kit for this. | ||
| SONY |
CCDV110
|
Hard case model number | Is the lcv-812 the correct hard case for the ccd-v110? -hq comments: yes, the lch-v200 may also be used. | ||
| SONY |
SLHF900
|
Assemble editing is not accurate | When assemble editing is used, the sl-hf900 could be off by asmuch as five frames. -hq comments: this is normal. the editing is not frame accurate. | ||
| SONY |
CCDF70
|
Forth title does not scroll | Customer claims the forth title of the ccd-f70 does not scrollis this normal? -hq comments: no, the forth title should scroll. | ||
| SONY |
D25
|
Incorrect part number for chassis assembly md | The part number of the chassis assembly md is incorrect in theservice manual. | ||
| SONY |
D9
|
Incorrect part number for q-430 | The part number for q-430 is incorrect in the service manual. | ||
| SONY |
D15
|
Incorrect part number of screw | The part numbers for reference no. 24 are incorrect in theservice manual. | ||
| SONY |
KV27HSR10
|
Buzzing on mts, see service bulletin number 46r1 | Buzzing in sound due to harmonics. | ||
| SONY |
KV2775R
|
Part number for a/v jacks, 1-536-970-11 | What is the part number for the audio, video jacks on the(u-1) board? -hq comments: jacks are part of the antenna terminal board part numberis 1-536-970-11. | ||
| SONY |
KV13TR20
|
Crt | Crt in unit has the crt, coil (degauss) and metal shield asone complete unit. replacement crt comes just with the crt. we need thecomplete assembly part number. -hq comments: there are two types of crts being used - one is in theservice manual. the o | ||
| SONY |
CCDF35
|
Extension cables | What are the part numbers for the extension cables thatconnect cn601 to w601 and cn801 to w603 between the (cv-8) and (cd-10)boards? |