Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
STRAV460
|
60hz hum on fm only | 60hz hum on fm only. q-804 was shorted. in addition, d-811which is a zener on the base of q-804 was shorted on this unit. | ||
| SONY |
STRAV760
|
60hz hum on fm only | 60hz hum on fm only. q-810 was shorted the b+ line to fm. itread 80 volts rather than the 2.7v indicated in the service manual. itwas putting about 1v ac on this line which was causing the hum. | ||
| SONY |
WMAF55
|
Part number missing - band switch knob | There is no reference in the exploded view for the bandswitch knob. it is not even shown in the exploded view. i need a partnumber for this knob. -hq comments: from tokyo (fax a891381): p/n is 3-346-595-02 which isthe same as the wm-af42. | ||
| SONY |
ICFPRO80
|
No single side-band operation | No single side-band operation. no osc from x1. c-79 open. | ||
| SONY |
CCDF50
|
Partially ejects and damages tape | Intermittent shutdown - would eject part way then reloadeating tape. | ||
| SONY |
CCDF70
|
No zoom motor drive | No zoom motor drive. | ||
| SONY |
STRAV700
|
After a few minutes the +/- 15v lines drop to 0v | The +/- 15v lines drop to 0v after a few minutes. | ||
| SONY |
D4
|
Intermittent no power | Unit does not turn on - but turns on when upper lid is pusheddown. the open leaf switch (s-801) does not contact well because the openleaf switch is bent or the pushing lever in the upper lid is worn out. | ||
| SONY |
D15
|
No spin/scraping noise during play | The height of the turntable is too low. it should be 1.5mm or2mm from md chassis. a disc does not spin because there is no gap betweenthe turntable and md chassis or the gap between them is just too small. adisc touches the md chassis intermittently. | ||
| SONY |
MDP200
|
Radio frequency interference | Unit had herringbone type interference caused by a.m. radiostation 850 k.c. whdh needham, massachusetts (approximately 1 1/2 milesaway). problem showed up in both video and r.f. out. the interference isa.c. line related. | ||
| SONY |
GEN-CAM
|
8mm lapping tape | What is the part number for the 8mm lapping tape? -hq comments: the part number for the 8mm lapping tape is 8-883-103-10. | ||
| SONY |
WMF100II
|
Tape will not play or excessive wow and flutter | Pinch roller touches part of cassette shell causing excessivewow and flutter or no play. | ||
| SONY |
STRAV900
|
Part number needed - insulating mica | Is there a part number for the insulating mica for the outputtransistors (2sc3856 and 2sa1492)? -hq comments: the mica insulators are shown on page 29 of the servicemanual as reference number 57. part number is also listed it is4-885-901-31. | ||
| SONY |
EVS700U
|
Lp mode playback picture is distorted with self-recording | Sp mode is ok. when i recorded and played it back in lp mode,one channel of ri waveform level is too small. | ||
| SONY |
CCDF40
|
Wrong part number for dt-71 board in manual | When servicer orders part number a-7061-127-a as in the manualfor the (dt-71) board, he receives an (aw-10p board). -hq comments: please change the service manual to the correct partnumber which is a-7068-127-a. | ||
| SONY |
SLV555UC
|
Transistor type correction | Transistor q-102 is drawn as a pnp transistor on page 83 ofthe service manual. | ||
| SONY |
CCDV3
|
Ccd-v3 lens hood | Is there a repair kit for the ccd-v3 lens hood? -hq comments: no there is no repair kit for this. | ||
| SONY |
CCDV110
|
Hard case model number | Is the lcv-812 the correct hard case for the ccd-v110? -hq comments: yes, the lch-v200 may also be used. | ||
| SONY |
SLHF900
|
Assemble editing is not accurate | When assemble editing is used, the sl-hf900 could be off by asmuch as five frames. -hq comments: this is normal. the editing is not frame accurate. | ||
| SONY |
CCDF70
|
Forth title does not scroll | Customer claims the forth title of the ccd-f70 does not scrollis this normal? -hq comments: no, the forth title should scroll. |