Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CDPC50
|
Part number for rear foot - reference number 35 | The original part number (x-4922-505-1) for the rear foot(reference no. 35) gets substituted to part number x-4922-508-1. thisfoot is too large in size. it is the size of the front feet of the unit.we need the correct part number. -hq comments: the re | ||
| SONY |
KV2782R
|
Incorrect part number in service manual | Part number in service manual (page 19, ref. no. 6)9-910-999-51, is incorrect. the same part number 9-910-999-51 is foundin the kv-2680r service manual on page 46, ref. no. 9 .... the samesolution applies. | ||
| SONY |
SPP60
|
No part number for speed dial label | There is no part number in the service manual for the speeddial label on the handset. -hq comments: faxed tokyo. their response was that this will not be asupplied part. they suggested that the customer make it themselves. wewill suggest to tokyo that | ||
| SONY |
SPP100
|
Replacement microphone is too small | The original part number (8-814-186-00) substitutes to a newpart number (1-542-092-11). the replacement microphone is too small. isthis a correct substitute? -hq comments: i have contacted tokyo with this question.11/20: the part number no longer subs | ||
| SONY |
RMX2
|
No part number for 12-pin socket | There is no part number listed in the service manual for the12-pin socket on the tuner in pcb (b board). the part number listed inthe service manual for reference no. 909 the pcb (1-625-386-11) is for theblank board only. | ||
| SONY |
CDPC7ESD
|
Broken pulley chucking | I have found the pulley chucking broken in several units. ihave replaced the pulley chucking and on a few units they have come backin a few weeks with the same problem. i found by melting and spreadingout center of the pulley chucking so it overlaps th | ||
| SONY |
CDPC70
|
Broken pulley chucking | I have found the pulley chucking broken in several units. ihave replaced the pulley chucking and on a few units they have come backin a few weeks with the same problem. i found by melting and spreadingout center of the pulley chucking so it overlaps th | ||
| SONY |
CDPC50
|
Broken pulley chucking | I have found the pulley chucking broken in several units. ihave replaced the pulley chucking and on a few units they have come backin a few weeks with the same problem. i found by melting and spreadingout center of the pulley chucking so it overlaps th | ||
| SONY |
CDPC40
|
Broken pulley chucking | I have found the pulley chucking broken in several units. ihave replaced the pulley chucking and on a few units they have come backin a few weeks with the same problem. i found by melting and spreadingout center of the pulley chucking so it overlaps th | ||
| SONY |
CDPC30
|
Broken pulley chucking | I have found the pulley chucking broken in several units. ihave replaced the pulley chucking and on a few units they have come backin a few weeks with the same problem. i found by melting and spreadingout center of the pulley chucking so it overlaps th | ||
| SONY |
CDPC26
|
Broken pulley chucking | I have found the pulley chucking broken in several units. ihave replaced the pulley chucking and on a few units they have come backin a few weeks with the same problem. i found by melting and spreadingout center of the pulley chucking so it overlaps th | ||
| SONY |
CDPC20
|
Broken pulley chucking | I have found the pulley chucking broken in several units. ihave replaced the pulley chucking and on a few units they have come backin a few weeks with the same problem. i found by melting and spreadingout center of the pulley chucking so it overlaps th | ||
| SONY |
SPP50
|
Spp-50 serial number same; channels different | Serial numbers on handset and base same but base unit usedchannel no. 10, while handset used channel no. 4. | ||
| SONY |
CDPC500
|
Incorrect part number | The part number in the service manual on page 20 shows thestep screw with the part number 7-685-666-79. this part number comes upas a standard thread black screw. the correct part number is needed. -hq comments: tokyo has supplied the correct part num | ||
| SONY |
CDPC400
|
Incorrect part number | The part number in the service manual on page 20 shows thestep screw with the part number 7-685-666-79. this part number comes upas a standard thread black screw. the correct part number is needed. -hq comments: tokyo has supplied the correct part num | ||
| SONY |
CDPC30
|
Incorrect part number | The part number in the service manual on page 19 shows thestep screw with the part number 7-685-666-79. this part number comes upas a standard thread black screw. the correct part number is needed. -hq comments: tokyo has supplied the correct part num | ||
| SONY |
CDPC26
|
Incorrect part number | The part number in the service manual on page 19 shows thestep screw with the part number 7-685-666-79. this part number comes upas a standard thread black screw. the correct part number is needed. -hq comments: tokyo has supplied the correct part num | ||
| SONY |
CDPC20
|
Incorrect part number | The part number in the service manual on page 19 shows thestep screw with the part number 7-685-666-79. this part number comes upas a standard thread black screw. the correct part number is needed. -hq comments: tokyo has supplied the correct part num | ||
| SONY |
SLHF860D
|
Tracking control has no effect | Fifty percent duty cycle pulse at pin 2 of ic-404. signalshould be varying pulse. 2v square wave set by the tracking controlbuttons. this signal is then sent to pin 3 of ic-001 (drum/capstan servochip). disconnected pin 2 ic-404. signal then shows n | ||
| SONY |
SLV50
|
Lp-4 kit installation causes irregular capstan operation | Capstan would intermittently not turn in loading-ff-rew modesand act sluggish also a constant audio warble in normal audio. thisproblem appeared after installing lp-4 kit with update ic-501 on (ma-27)board. |