Sony Repair Tips
Search: sony
Results: 20073
Results: 20073
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CDXR7
|
Sled intermittently will not move | Intermittently the sled would not move from its innermostposition. when in the failed state the outputs q509-511 would get verywarm. | ||
| SONY |
KX2501A
|
No start up, replaced t653 | Set would not start up. b + 320v, and 160v present on gaboard. troubleshooting showed only a negative going pulse to the base ofq652. also there was no pulse on the base of q651. located defectivet653. | ||
| SONY |
CDP302
|
Part number incorrect in s/m | Part number listed in service manual on page 58 item 79 is4-308-840-00. this is the incorrect part number. | ||
| SONY |
SLHF900
|
Eats tape | Very intermittently coming out of beta-scan, reel motor slow,but not capstan. results are tape damage since tu reel cannot wind itfast enough. -hq comments: problems of this nature are difficult to find. as wediscussed, if you send the unit to us we w | ||
| SONY |
CCDV8AFU
|
No camera video | On cx23047b one pulse was missing. i think this is part ofmaster osc. giving color prob. | ||
| SONY |
SL2500
|
Part number for table assy (cap only) | No part number for table assy - cap only - ref #705 (cap fort-reel table). -hq comments: this part is not available, nor is the reel table. | ||
| SONY |
BMC550
|
Missing part and part number | Need p/n for four screws that fit into ref #374 on page 109.these screws are not shown in the pictorial. -hq comments: the part number for the screws is 7-685-862-09. forscrews bvtt 2.6 x 6. | ||
| SONY |
XR740
|
Wrong labelling of head pc board switches | On page 41 of s/m for xr-740, 747r, 780 and 787r, thehead pc board switches are labelled incorrectly. your recent s/b #62 hasthem labelled incorrectly. the parts listing on page 41 also has themincorrectly. s701 is on page 41 of the manuals, but you h | ||
| SONY |
XR66
|
Reference number correction | On page 38 of the service manual for xr-66, and on page 34 ofthe service manual for xr-80 the head pc board switches are labelledincorrectly in the parts breakout and listing below. -hq comments: we will issue a service bulletin. | ||
| SONY |
STRAV460
|
Volume changes are not linear | Volume changes are erratic and jumpy when trying to changelevels with volume controls. tried changing ic601 to no avail. all otheroperations are ok. i have seen similar problems on model ta-ax520amplifiers also. this is a constant problem. -hq comme | ||
| SONY |
WMF1
|
Incorrect part number | Part number listed in service manual is incorrect. | ||
| SONY |
WM8
|
Incorrect part number | Part number listed for the p/b head in service manual isincorrect. | ||
| SONY |
STRAV560
|
Missing part number | S/m does not list a part number for the front panel. -hq comments: part number for front panel is x-4906-723-1 for str-av560 x-4906-713-1 for str-av760 | ||
| SONY |
EVC8U
|
No eject | Unit would load ok. play tape for a few seconds then stop.ff or rew would run for a short time then stop. when eject was pushed thetape would unthread, but cassette compartment would not come up. the modeswitch was not running, it was staying in the l | ||
| SONY |
ITA500
|
Low volume on ogm and icm signal to telephone line | Customer complains that ogm and icm volume is low and cannotbe heard if phone line quality is a little low. also, mentioned he isdissatisfied with seizing line with 1 1/2 rings. -hq comments: a modification is presently being investigated to increaseit | ||
| SONY |
EVS700U
|
Intermittently take up after pause released | Item #371 on page 155 of s/m rubbing against a piece ofbad molding beneath it. | ||
| SONY |
D7S
|
Disc will not spin | The unit would not spin the disc. this was caused by thethrust screw coming loose and allowing the rotor to bind. readjustmentresolved the problem. this is becoming a common problem with this unit.depending on how far out of adjustment the thrust scre | ||
| SONY |
CCDV8
|
No rf output from modulator | All functions worked except there was no rf from the rfmodulator. audio and video lines worked fine. | ||
| SONY |
KV1944R
|
Snowy pix, no sound, replaced ic2006 | Has snowy picture, no sound, no display. power on/off ok,could not tune channels. | ||
| SONY |
STRVX750
|
Shutdown | Unit would come on for a few seconds and shut off. this wasintermittently. found with signwave input that right on out had ringingand spike on output. found r783 had changed value 39Ω. changed, sameproblem. |