Toshiba Repair Tips
Search: toshiba
Results: 5617
Results: 5617
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| TOSHIBA |
2527DB
|
Dead , power and timer leds flashing ht 40v and var | Q828 2sc2230a-y | ||
| TOSHIBA |
2527DB
|
Crackle on nicam , fm. and ext power supplys | Icg07 audio processor ( ta8776n ) back terminal board | ||
| TOSHIBA |
2512DBT
|
Won't go into st/by | 2sc2032 (not 2sc2033) | ||
| TOSHIBA |
2512DBT
|
Whistling , crackling , popping poor sound. | Redress scan coil , nicam signal leads. | ||
| TOSHIBA |
2512DBT
|
St/by cannot be initiated | S/c tr in psu | ||
| TOSHIBA |
2512DBT
|
Service mode access | Press the "f" button & video input button together on r/c. enter "1048" r/c; "m" appears at the top right hand corner of screen. hold "f" button & press picture menu button - menu item up. hold the "f" button and press the sound menu button - menu item down adjust using the volume "+" and "-" buttons - go to standby to store and exit. | ||
| TOSHIBA |
2512DBT
|
Poor nicam with whistle cracking/popping | Redress scan coil leads and digital data leads | ||
| TOSHIBA |
2512DBT
|
Lack of height & wobbly outlines | Elects (esp brown ones) in hor driver module | ||
| TOSHIBA |
2512DBT
|
Height reduced & e-w bowing | C372 2µ2 & c374 220µ in dpc module | ||
| TOSHIBA |
2512DBT
|
Field - lack of height with bottom compressed | C372 2µ2 under screening can on dpc board | ||
| TOSHIBA |
2512DB 2812DB C91SB
|
Poor width , corrugated effect on side of picture . | C424 4u7 ptno24676479 | ||
| TOSHIBA |
2512DB
|
Wont go to sby | Q845 ( 2sc2033 - toshiba 23314246 ) | ||
| TOSHIBA |
2512DB
|
Stuck in stby if pin 64 ica01 ok at 5v check pin 3 | Replace ic805 pt no23318232 | ||
| TOSHIBA |
2512DB
|
Static discharge from speaker grills | Use statkit to directly connect grills to chassis ( supercedes july bulletin re fitting new cabinet ) | ||
| TOSHIBA |
2512DB
|
Shrunken and non-linear frame | C372 (2u2f 50v), c374 (220uf 16v), c372 (2u2f 50v) which are all mounted under a screening can on a sub panel at the front right (as seen from the rear). also c317 (2u2f 50v) positioned under the overhang of the sub panel on the main board. | ||
| TOSHIBA |
2512DB
|
Psu trips one minute after switch one, could be int or random | Ground pin 52 of ic501, ref toshiba technical | ||
| TOSHIBA |
2512DB
|
Non lin field | Caps (2µ2 & 220µ) in screening can on small pcb back rhs of main pcb | ||
| TOSHIBA |
2512DB
|
No st/by, small raster after loptx replacement | Q845 st/by sw tr 2sc2023 - but12a used in lieu | ||
| TOSHIBA |
2512DB
|
Low width + ew fault r425 oc | L423 short turns | ||
| TOSHIBA |
2512DB
|
Lack of width. | R425 o/c , loading coil l423 ( tx100 ew pcb ) width , ew adj via h/set |