Philco Repair Tips
Search: philco
Results: 4838
Results: 4838
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
PHILCO |
TP2054
|
I didn't get normal AV channels | Sf 201 | Replace sf 201, and run for the hug | chines eletronica/ solanea PB |
PHILCO |
TP 1453
|
Turns off standby, flashes quickly and turns on standby again, and doesn't turn on | R 750 3k3 oscillator | pedrinho tela quente | |
PHILCO |
PH29MSS
MA1 |
Low power supply, LED flashes when the keys are pressed | Transistor q808 | To replace | kleber show |
PHILCO |
PH29M SS
|
Turns on, discharges and turns off. LED keeps flashing and no longer turns on. | C846 47x100 | Swap c846 | TonicoBH |
PHILCO |
PCS-2952
|
After a while it is on, it turns off and tsound is noise at the power supply.... | Replace cap. 220/200v... | ||
PHILCO |
2044
|
Upper vertical lines looks like a 100uf capacitor but it is not | See r 610 open | Master Eletronica | |
PHILCO PCM |
14
|
Vertical closed a little at the top and a little at the bottom with a luminous streak at the bottom | Eprom It's just replace | MARCIORVGO | |
PHILCO |
PCS 2976
|
Turning off when changing channels and vertical a little closed at the top | I replaced the 39u 250v c728 with a 53u 250v and it is working perfectly, as the 39u was replaced and nothing happened, even the channels gained performance! | Fabiano | |
PHILCO |
PCS2952
|
This TV had a leaking flay back, I replaced it and when I turned it on the TV it had a red screen I thought it was the resistors on the kinescope board but it wasn't. | I had to do a procedure that is as follows: turn off the TV in general and hold down the two channel keys and turn on the TV, and hold for three seconds, and everything will return to normal. | ELETRONICA DIGI SOUND, NOVA TIMBOTEUA PA | |
PHILCO BRITANIA |
PH14D
|
Led flashes radido No start r839 82k rising c 843 c 845 also varies in memory | Grava eprom | PHILTEC | |
PHILCO |
TPF2121
|
The LED turns on, presses power, the LED goes off for a few seconds and starts flashing | Wide capacitor | edezio eletronica | |
PHILCO |
PH21M SS
|
ñ league not led | Diodo zener 18v q 802 r402 r846 10Ω d 811 | Replace e so file | fofinho |
PHILCO |
TP2052N
|
Doesn't start | Power supply transformer with loose ferrite and open r921 and 923 | Paste trafo and replace resistances for 1r | ELETRONICA MAURI JUNIOR |
PHILCO |
PH21SS
|
Vertical closed at the bottom | -13v missing from the vertical diode with poor contact and 1000/25v capacitor with low capacitance | orlando lott | |
PHILCO |
PCM-2046
|
LED blinks and doesn't turn on | C911 sold out | Replacement | beto |
PHILCO |
PH21D
|
Turns off after turning on | Excessive width, high power supply with 130v instead of 105v | Test r 839 82k replaced to 100k. | LOU |
PHILCO |
TP2052
|
Call whenever you want | Trafo from sole nucleus power supply | Glue and tape | ELETRONICA MAURI JUNIOR |
PHILCO |
TP2025
|
Call whenever you want | Power supply transformer with loose core | Glue with glue and apply insulating tape | ELETRONICA MAURI JUNIOR |
PHILCO |
TVPH21MSS
|
Vertical reduced almost completely and colored stripes in the center | D-301 amended | Replace d-301 fr104 | samuel leite |
PHILCO |
PHT550
PHT550 |
Burned fountain | After changing the cap. 120x200 primary power supply and 13005 + r15 and r52 it still wouldn't turn on and a humming noise heated up the t1 and t2 | D18 and d20 ---- shorted after the replace, it worked 100% again | neupsx4download |