Philco Repair Tips
Search: philco
Results: 4811
Results: 4811
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
TPF2121F
|
Remote doesn't work | Leak between the sensor terminals, change it, or, in my case, scrape off the epoxy a little between the terminals and also between the contacts and the ground and also change the two 10 uf capacitors that are connected to it | ||
| PHILCO |
TP1453
|
Vertical a little closed | Service mode | Adjust | Mauro Mascarenha - Parazinho Ceara |
| PHILCO |
PCM2046
|
Turns off after a while. | Ic701 e c720. | R-TEC Eletrônica | |
| PHILCO |
PHILCO PH21B
|
Tsound are 2 defects, 1 turns on after 1 min + or - darkens and turns off 2 closes a little horizontally with retraction | V502 ou o c2383 | MARCIORV | |
| PHILCO |
TV-PH21C
|
Low power supply, LED does not turn on | Q881 changed | JOELTON | |
| PHILCO |
PH21M SS
|
TV inoperative and led pool | Change from-811 to-813(byv95) dz18v in the line of r818 q-802 and r826 | samuel leite | |
| PHILCO |
TPF2121C
|
TV turns on with sound popping and no image and turns off | R910 and r912 open | Just replace and run for the hug | Junio kleber |
| PHILCO |
PH21 MSS
|
Does not leave st. by. Because of a memory problem, I posted this defect and forgot to say that if anyone needs the eeprom, ask me by email: |
Memory swap | reinaldo almeida | |
| PHILCO |
PH29M SS
|
Low power supply around 40v LED goes out but the TV doesn't turn on the power supply stays the same | C851 .1 with leakage is at the base of q808 | Replace c 851 | Damião |
| PHILCO |
TV PH21MSS
|
Does not leave st. by. | Memory, but be careful, I had already installed another one that I recorded with files downloaded from the internet and it didn't work, it only worked when luckily another TV like it came on and I copied the files and switched to the one that had the problem. | reinaldo almeida | |
| PHILCO |
PH21M SS
|
When turning it on, the LED flashes, +b changing to 24v | D818 =fr104 shorted | Replace it and run for the hug | hipereletronica service (maraial-PE) Marcelo |
| PHILCO |
PH 21C
|
Turns on with vertical closed, then turns off | D 810-replace open diode | MARCELO JOSE | |
| PHILCO |
TTV PH 21C
|
TV does not turn on any voltage on the secondary | Zener diode 12v short non-primary d821 | Darci Fuhr | |
| PHILCO |
PH24A
|
Does not turn on, power supply stopped | C203 (2n2/ 1kv polyester capacitor) shorted | Aecio Flavio | |
| PHILCO |
PCS2956
|
Risk on the image, better known as the delay line, which is generally seen on the c728 3n3 1600v | C728 3n3 1600v was replaced | gerson tomaz | |
| PHILCO |
PH29
|
Does not turn on low power supply | Zd804 (4v7) | mega center | |
| PHILCO |
TPF-2922
|
Vertical burnt out, the biggest problem to fix, I used a similar part and it never worked. | The resistor that comes from the 50volrs of the flyback is 18r and the ci tda8177f or tda9302h tsound is no point in putting the tda8177 | Put the correct parts and that's it, blz | fabiusmax |
| PHILCO |
PCM-2046
|
The standby LED doesn't turn on, it's flashing, only the flyback is defective, be careful friend, even with the +b and the bu disconnected, the power supply is low @@@ | Flyback | ELETRONICA ARNI/LEOBERTO LEAL-SC | |
| PHILCO |
TPF2922
|
Burnt resistor r709 | Value of resistor r709 is 18r 1/2 if you put lower values it will burn type 1r it will catch fire | fabiusmax | |
| PHILCO |
PCM-1451
|
Call whenever you want, it seems like a bad connection | Intermittently turns on and off... | Changing capacitors c 709, c708, changing both without measuring.... | Adriano,rio verde,MS |