Philco Repair Tips

Search: philco
Results: 4811

Make	Model	Symptom	Problem	Solution	By
PHILCO	PH14B	No picture, normal sound	Press the at key on the original remote control	If the image appears, disable the at enable function in services mode	paulorusso
PHILCO	PH21B	No picture, normal sound	Press the at key on the original remote control	If the image appears, disable the at enable function in services mode	paulorusso
PHILCO	PH29B	No picture, normal sound	Press the at key on the original remote control	If the image appears, disable the at enable function in services mode	paulorusso
PHILCO	PH29B	Normal image, no sound...	C833 e c829 de 1000uf 25 v	In my case, the c833 was stμFfed, I replaced it and the sound came back normal.	vilenon
PHILCO	PH29B	Power supply does not arm, in this case tsound is only primary power supply and not secondary	Q806 ,bc1815 with small leak.	Replace it without testing and the power supply will arm...	vilenon de oliveira
PHILCO	TV PH 21A	Normal image but no sound	V173 changed		sandro
PHILCO	TP2054	Inoperative /led blinks weakly with little brightness	Zd906 altered!		orlando lott
PHILCO	TPF29S4F	When you press the power key, the power supply goes off for a few seconds, then disarms and activates the protection	Check capacitor c1703	Replace the same	Mario Teilor o da penha
PHILCO	TPF29S4F	Hitting relay	Open resistor r919	Replace the same value 120k 0.4w metal	Mario Teilor o da penha
PHILCO	PCS 2976		Cap. 715 (2k2 / 1600v) aberto		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	PH21C	Power supply pulsating flashing led	Ic803 (tl431)com flake	Replace the same	jean alves
PHILCO	PCM2046	Red screen instead of blue screen	Memoria 80011a	Reset the memory by pressing all the keys at once with the TV off and on. If that doesn't work, you have to replace the memory. In my case it resolved.	Fábio
PHILCO	PCM2046	TV arrived with Stanby LED blinking trying to activate horizontal. voltages +b 95v, +20v, +5v and +9v normal. tsound was no +26v.	I found r720 1r open. changed, it activated protection and the other voltages no longer existed. After much analysis I discovered c725 470uf/35v inverted and already inflated.	I replaced c725 and it started working again.	Fábio
PHILCO	PCM2046	TV arrived with Stanby LED blinking trying to activate horizontal. voltages +b 95v, +20v, +5v and +9v normal. tsound was no +26v.	I found r720 1r open. changed, it activated protection and the other voltages no longer existed. After much analysis I discovered c725 470uf/35v inverted and already inflated.		Fábio
PHILCO	TP 2920 CP02R0	Try to turn it on and turn it off	C 1703 with 6n8 drops to less than 4n and puts d by 228 on the run	Replace it and in place of the by228 ask to put the by329 which works well, note these diode are damper 1500v 7a.	cetrel eletronica
PHILCO HITACHI	PC1603	It doesn't turn on, tsound's a noise, tsound's no 115v on the +b @@@	R914=1oor changed and bad flay even outside it is without the 115v of the b+ resolved		ELETRONICA ARNI/LEOBERTO LEAL
PHILCO	PCM-2046 CPH 05	If you connect an antenna or AV cable, it oscillates and returns to standby, without the cable it turns on normally.	Flyback b 32-3454		Henderson(hndrsn)
PHILCO	PH21SS 21C1PH02-2H	Vertical closed bottom, check power supply capacitor c562, if tsound is no current, replace diode ud564	Replace ud564 diode without measuring because it measures normally and doesn't work		fabiusmax
PHILCO	PH21SS	Image with little brightness, or darkening until it is completely dull.	Bf422 positions v912, v922, v932 Attention, do not test, replace for new ones!		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	TV PH21USA1	Works after a few minutes closes on the sides and cuts the sound	Transistor v553 (c1815) alterado cap. 22/50v		This email address is being protected from spambots. You need JavaScript enabled to view it. (Bruno)