Philips Repair Tips

Search: philips
Results: 14207

Make	Model	Symptom	Problem	Solution	By
PHILIPS	PT316 14PT316A	Reduced frame at the top of the screen	Measure voltage scl and sda		dede som
PHILIPS	14PT1332/11 L6.1	Does not start, makes noise (wheezing), output on transistor "7504" 30v~ wsound it should be 96v	330p 3kv "2501" capacitor in resistance, just change capacitor		jramalho
PHILIPS	21PT9467C/78 SK4.1L	Retrace, white lines on the screen	R 3186,8 homs	Replace r 3186,8 homs	johnny busnadiego
PHILIPS	HTS3152-55	Doesn't start	Plug it into the socket and the LED blinks and turns off, it remains without 3.3 and 1.8	Replace the sa5888s servo motor	Lelo
PHILIPS	14PT316A/78	Does not tune in, turns off in 10 seconds	C47 mf 160 v tda 7056b saida h bul312 fp	Replace them all	Nara
PHILIPS	20PT3331/78R	Stand by LED lights up, presses channel, but does not turn on at all	Hand coupler		lord
PHILIPS	14PT133A	Does not tune in, turns off in 10 seconds	C47 mf 160v tda7056b saída h bul 312 fb	Replace	nara
PHILIPS	29PT4635	Turning it off, several screen-adjusted components were checked and it didn't solve the problem.	It was only resolved with another tube	Replace for another good one	eletroclaudio aguas belas
PHILIPS	14GL1015	Image out of tune	Touch tda8360		silva2
PHILIPS	16GL1332	Blurred image	Bad flyback causing the burning of r522,555,556,c556, these components worked normally but with a blurred image without contrast considering the damaged ts557.	Replace sem mdir ts557 bc558	PALAURO
PHILIPS	20PT3336	Turns off as soon as the image appears, you notice colored shadows on people	Weak tube.	Replace tube	tyko
PHILIPS	21GX1668/78R	Volume increases to half and freezes characters	Memoria eproom	Replace	afonso
PHILIPS	14PT314A L9.2A	Tda9302h getting hot when changed.	Replace capacitors c2465, c2466 and c2467 with new capacitors with higher insulation voltage in the case of 100 volts. Tsound's no point in measuring, you have to change it.		jedvaldo
PHILIPS	21PT8467	TV has audio and also sound in AV. but no sound with varicap input	Change eproom, in this case, at 24c16 wp. hugs ...		POLYSOM
PHILIPS	DVD625/782	It doesn't turn the disc, it tries to start but then stops.	This device causes a lot of problems with the 2 motors, the spindle and the charging one, check them both on the 1Ω scale of the miter, they have to give 100Ω or more if they do, they are good, then you can check the flat if it is old with a lot of bending, change it, also at mpeg board a c8 capacitor, I hope I helped you!!!		apdo - ardldvd
PHILIPS	29PT5642/78	Vertical closed position with three colored lines at the bottom of the tube, in 15 seconds the protection was activated	Diodo d 6457 capacitor c2463(100uf 50v) c2465 (10uf 100v)		lucio This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	20PT5294 /78	Stopped .dead power supply	Bad tea1507 I changed it, solved it		ELETRONICA IDEAL
PHILIPS	20PT3331	Turning on and shortly after turning off with upper lines and partially closed at the top	The polyester capacitor measuring 683k x 250v, or 100 nanofarads x 250v, it was measuring around 17 nanofarads, its location on the board is c2460 close to the flayback	As a precaution, also replace the following capacitors .c2465, c2446, c2444, c2463, c2405, c2564. without testing thanks guys	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	25PT5541 L04	No sync	Replace capacitors 2235 and 2236		johnny busnadiego
PHILIPS	21PT5433	Vertical opens only half and with retraction lines at the top	Change the 6460 diode		MACCELETRONICA