Philips Repair Tips
Search: philips
Results: 14232
Results: 14232
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
20PT3336
|
Power supply stays from 50 to 70v, TV does not oscillate, LED lights up normally and when giving power it spsgs normal, but of course horizontal does not oscillate. | See photocoupler | Replacement | Master Eletronica |
| PHILIPS |
29PT5642/78
LO4 LS1 |
Noise that increases when the brightness increases | Changed resistor r3606 from 39k to 27k | Carlos Lucio | |
| PHILIPS |
14PT3131
|
I'm sound | TV full of undesirable insects (cockroaches, ants, etc.) | Carried out general internal cleaning/replacement of the open speaker | lpinheiro |
| PHILIPS |
20PT3331
|
No sound, or low sound | C2444 | guitec | |
| PHILIPS |
20PT122A/78R
|
Doesn't start | C2447 was leaking | Replace and run for the hug | serginhosond@yahoo |
| PHILIPS |
PT316
14PT316A |
Reduced frame at the top of the screen | Measure voltage scl and sda | dede som | |
| PHILIPS |
14PT1332/11
L6.1 |
Does not start, makes noise (wheezing), output on transistor "7504" 30v~ wsound it should be 96v | 330p 3kv "2501" capacitor in resistance, just change capacitor | jramalho | |
| PHILIPS |
21PT9467C/78
SK4.1L |
Retrace, white lines on the screen | R 3186,8 homs | Replace r 3186,8 homs | johnny busnadiego |
| PHILIPS |
HTS3152-55
|
Doesn't start | Plug it into the socket and the LED blinks and turns off, it remains without 3.3 and 1.8 | Replace the sa5888s servo motor | Lelo |
| PHILIPS |
14PT316A/78
|
Does not tune in, turns off in 10 seconds | C47 mf 160 v tda 7056b saida h bul312 fp | Replace them all | Nara |
| PHILIPS |
20PT3331/78R
|
Stand by LED lights up, presses channel, but does not turn on at all | Hand coupler | lord | |
| PHILIPS |
14PT133A
|
Does not tune in, turns off in 10 seconds | C47 mf 160v tda7056b saída h bul 312 fb | Replace | nara |
| PHILIPS |
29PT4635
|
Turning it off, several screen-adjusted components were checked and it didn't solve the problem. | It was only resolved with another tube | Replace for another good one | eletroclaudio aguas belas |
| PHILIPS |
14GL1015
|
Image out of tune | Touch tda8360 | silva2 | |
| PHILIPS |
16GL1332
|
Blurred image | Bad flyback causing the burning of r522,555,556,c556, these components worked normally but with a blurred image without contrast considering the damaged ts557. | Replace sem mdir ts557 bc558 | PALAURO |
| PHILIPS |
20PT3336
|
Turns off as soon as the image appears, you notice colored shadows on people | Weak tube. | Replace tube | tyko |
| PHILIPS |
21GX1668/78R
|
Volume increases to half and freezes characters | Memoria eproom | Replace | afonso |
| PHILIPS |
14PT314A
L9.2A |
Tda9302h getting hot when changed. | Replace capacitors c2465, c2466 and c2467 with new capacitors with higher insulation voltage in the case of 100 volts. Tsound's no point in measuring, you have to change it. | jedvaldo | |
| PHILIPS |
21PT8467
|
TV has audio and also sound in AV. but no sound with varicap input | Change eproom, in this case, at 24c16 wp. hugs ... | POLYSOM | |
| PHILIPS |
DVD625/782
|
It doesn't turn the disc, it tries to start but then stops. | This device causes a lot of problems with the 2 motors, the spindle and the charging one, check them both on the 1Ω scale of the miter, they have to give 100Ω or more if they do, they are good, then you can check the flat if it is old with a lot of bending, change it, also at mpeg board a c8 capacitor, I hope I helped you!!! | apdo - ardldvd |