Sony Repair Tips
Search: sony
Results: 20073
Results: 20073
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
KV32S15
|
Relay pulsates on and off, replaced pm501 | Relay ry602 pulsating on and off continuously. | ||
| SONY |
KV27XBR95S
|
Scrolling bar distortion, resoldered c529 | Screen distorted horizontal lines scrolling, can see throughbars. solution: c529 loose resoldered all ok. hq comments: located off of ic503/pin 2 on the a board. couples the hpulse to the pin correction circuit. | ||
| SONY |
KV27XBR35
|
Pip rolling vertically and shutdown, rosolder q323 on e1 brd | Intermittently, pip started rolling vertically, few secondslater pip and main picture blanked, another few seconds and shutdownactivated. pin38 of e1 board had no vertical pulse which provides syncto p1,p3, m and e2 boards. found cold solder q323 col | ||
| SONY |
KV27V55
|
Buzz in speakers, see sb 250r1 | Customer complained about slight buzz from speakers. this is the same problem that j. kolokithias had in pa. it also happens that this svcr is in pa. same problem as i reported on kv27xbr37. -hq comments: please r | ||
| SONY |
KV27V10
|
No auto program function, respldered r062 | Unit would not auto-program. feature would not work due toabsence of h sync at ic101/pin 28. problem cuased by poor solderconnection on r062 in the base circuit of q0001, m board. sync separatorcircuit which inputs to ic101/pin 28. resoldering solve | ||
| SONY |
KV27TS29
|
Intermittent brightness, replaced r526 | Brightness does not always come on. found r526, 220k open. | ||
| SONY |
KV27S15
|
Intermittent no channel change(but osd change),r005 on m brd | Unit would intermittently not change channels, but the osd would indicate that the channels were changing. | ||
| SONY |
KV27S10
|
Vertical down about 2 in from top, replaced r539 & ic101 | Vertical was down about 2 from top. checked voltage on tp98and read 1.8v. tech determined to be fbt. replaced fbt with sameproblem. checked another set and tp98 should be 11.8v not 15v asschematic states. traced problem to r539 had changed value from | ||
| SONY |
KV27S10
|
No picture, replaced r701 | No picture but has sound. found low voltage on g2 pin5 crt socket... found r701 open. | ||
| SONY |
KV27FX10
|
No picture sound ok, replaced r542 and d809 | No picture, but sound is ok. | ||
| SONY |
KV27EXR25
|
Unit shut down, replaced ic101 | Shut down intermittently. osd had a 60hz bend only osd picture perfect. | ||
| SONY |
KV20VM20
|
Tiny hor.line in middleof screen,ic301/pin 7 re-soldered | Tiny horizontal line that split screen in middle.replacing ic1301 didn't hold. found crack on foil connected toic-301/pin 7. | ||
| SONY |
KV20VM20
|
No audio, replaced fl401 | No audio signal at the audio input connector p1602/pin 1 onthe d board. nor at the base of q451 on the ma board. audio waspresent at ic401/pin 14 . found filter fl401 located between ic401/pin 14 and the base of q451 was open. | ||
| SONY |
KV20S10
|
1/3 of picture is blankout, resoldered flybackpin 8 | Pix 1/3 up screen, no video just raster, bottom 1/3 of pix isblack not scanned on. -solution :replaced ic501, believe vert problem? turned out that 13vwas low, 11v, found out pin 8 of fbt bad joint resoldered pin 8 set ok.do not understand why 13v lin | ||
| SONY |
KV20S10
|
Intermittent tuning, replaced tuner | Channels get static then come on. | ||
| SONY |
KV20S10
|
Dead, npf, | Dead. | ||
| SONY |
KV20S10
|
Picture flips, adj vfre | Picture flips. | ||
| SONY |
KV13VM20
|
No picture, replaced crt | No picture, sound ok. | ||
| SONY |
KV13TR24
|
Intermittent no picture or snow, replaced leaky d101 | Unit would go to snowy or intermittent picture. | ||
| SONY |
KPR46XBR25
|
No video, replaced q1605 on a board | No raster, when g2 was increased on all 3 crts raster appeared with retrace lines and raggedy edges, only when reducing g2 voltage on green crt, video would be visible momentarily. |