Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
WMF2031
|
Wrong part number for ic-301 | The p/n listed in the s/m for ic-301 (8-759-820-21) isincorrect. | ||
| SONY |
TAAX301
|
Wrong part number - front panel assembly | The correct part number is x-4911-213-1. -hq comments: a service bulletin will be written to forward thisinformation to the field. thanks for the information. | ||
| SONY |
FHB5CD
|
Wrong part number power cord (us) | The correct part number is 1-575-706-11. -hq comments: thanks for the information. a service bulletin will bewritten to notify the field. | ||
| SONY |
CCDV5000
|
No audio for 1 1/2 seconds after pause | When customer takes unit out of pause mode, he has no audiofor 1 1/2 seconds. this causes a problem when editing. -hq comments: this is normal operation. the audio must be muted untilthe servos come up to speed, otherwise there would be noise from the | ||
| SONY |
KV32XBR65
|
Srs distortion, see sb 45r1 | Srs distortion.solution: replaced srs moduel -hq comments: please replace the moduel with the new one as perservice bulletin 045.srs moduel 8-741-592-02moduel bracket 4-393-435-05 | ||
| SONY |
ITK500
|
Compatibility problem with pcb, tel-key(new version) | The new version of the pc board, telephone key part number1-618-217-11 has only 8 wires out of its connector. the old board and theservice manual shows 10 wires out of the connector. is there anycompatibility problem between the two boards? -hq commen | ||
| SONY |
SLV373UC
|
Part number for tk-7 board | The part number in the service manual for the tk-7 board(1-634-742-11) indicates part not found both in kc and rpc. is this agood number? can you please advise? -hq comments: this board is not available as a replacement part. | ||
| SONY |
CDPC705
|
Torn print on pcb | When you remove ic-102 with pyro pen, too much glue has beenput underneath ic. when you try to remove the ic, the print tears up thecircuit board. -hq comments: the glue used is necessary during the manufacturingprocess to secure the components to the | ||
| SONY |
CDPC85ES
|
Torn print on pcb | When you remove ic-102 with pyro pen, too much glue has beenput underneath ic. when you try to remove the ic, the print tears up thecircuit board. -hq comments: the glue used is necessary during the manufacturingprocess to secure the components to the | ||
| SONY |
CCDF30
|
No eject | Intermittent - won't eject or play. | ||
| SONY |
KV32XBR50
|
Excessive horizontal size (hor. overscan),l501 | Q-505 (pin-out) and q-503 (h-out) were both shorted. whenreplacing these defective components, there was excessive horizontal widthon screen. h-size could not be adjusted to normal size. found l-501shorted. good coil reads 4.9Ω. defective coil r | ||
| SONY |
CDPC75ES
|
Torn print on pcb | When you remove ic-102 with pyro pen, too much glue has beenput underneath ic. when you try to remove the ic, the print tears up thecircuit board. -hq comments: the glue used is necessary during the manufacturingprocess to secure the components to the | ||
| SONY |
XR7087
|
Part number correction | The part number for the knob assembly tone on page 17 (ref 11)is incorrectly listed in the service manual. | ||
| SONY |
CCDF55
|
Intermittent shut down | Unit would intermittently shut down after displaying head clogdetection. further investigation showed the unit was unable to detectspeed during cue and review. went to ic-507 pin 1 was 5v not 0v. pin 2never went to 2.9v and pin 1 never output the dete | ||
| SONY |
CDPC75ES
|
Erratic drawer operation and no play | Drawer opens and closes but continues to attempt to load.after a few seconds, the motor cuts off but no focus search. if allowedto cycle without interference the drawer would open again. | ||
| SONY |
KV2791R
|
Picture is dark, replace q-356 | Original problem - unit was dead. after locating problem, nowpicture was dark. | ||
| SONY |
SBV900
|
Unit has no output | When checking voltage levels, i found the regulated +12 voltsto be missing out of ic-001 on the pw-92 power supply pc board. | ||
| SONY |
CCDTR4
|
No power | F-903 open - replaced and it opened again. found short on vtrline c-522 shorted. | ||
| SONY |
CDP391
|
Door will not open - intermittent | Disk tray will not open. when tray is closed, s-191 load-outswitch has 2vdc (this is ic-201 pin 63) should be 5v when tray is closed. | ||
| SONY |
SLV555UC
|
Part number of tension regulator arm assembly | There is no reference or part number in the service manual forthe tension regulator arm assembly. |