☰

Cce Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: cce
Results: 4824
Make Model Symptom Problem Solution By
CCE HPS 21AVP
AVP 		Black bar on the left side of the TV C-417 331x2kv ceramic capacitor next to the fly-back Replace it without testing ELETRONICA CAVALCANTE MARTINOPOLE-CE
CCE TV29USP
Distortion similar to an upright bowl, reel or guitar Cold soldering Resoldar o q406 ESEQUIAS SANTANA
CCE HPS2071
JJ 		League gets flyback cutting high voltageSuspected flay It's not a defect in the flat Saida is vertical fernado tj maçeio
CCE HPS 1471
Doesn't start C805 without capacitance and dz801 18v in short simas433
CCE TV2918USP MEK
Image without definition and drizzle Cause: leaky transistor v933 bf423 klein
CCE HPS-1497/2097
Does not turn on secondary power supply zero voltage Check the entire line of pins 2,6,7,9,11 and 14 of the power supply (ic-801). _I found the capacitor c-839 (470pf/50v) smd low capacitance, on line di pin 11 of the ic-801, I replaced this capacitor and the TV worked - perfect. I put a ceramic one. Help yourself leave your tip ELETRONICA ARNI-SC /L.LEAL
CCE TV2118USP/AV
Black stripe on the right side of the screen C417 ceramic nauany
CCE HPS2097
Horizontal and vertical vary depending on the intensity of the brightness Changed power supply C825 (47u/160), c929 (33u/160v), ic803 (photo coupler), q804 (bc337) and q802 (bc337) Eletrônica Staub
CCE 2065
When the channel has no emitter, the circuit leaves the horizontal frequency Change the la 7680 and adjust the f h WARLEY CESAR
CCE HPS2991
Normal power supply, low horizontal, normal 13v, 51v with 17v Q409 tonico
CCE HPS1471
The LED is off and the +b voltage varies Ci tea1533at samuel leite
CCE 1402E
Horizontal with image flipped C 404 1uf x 100v Is to replace and work Leildo Keys
CCE HPS1481
Nothing works and the power supply capacitor remains charged Power supply drive transformer with insulated wire on the primary, next to the pin Solder very carefully using a very thin wire. Ádrian Chapadão do Céu-Go
CCE HPS 2185FS
When you change the TV channel. activate the relay R 913 amended ercilio fabricio
CCE HPS-2073
Turns it on and off, increasing the screen you could see the vertical closed Q 802 bc 337 behind the ch key - change without measurement also check r822 6r8 Osmildo, Nova Lacerda MT
CCE HPS2189
Turn on and off Change the start key julio.sertemaq
CCE HPS1497
No image just character 4v7 zener diode 201 with leakage klein
CCE HPS2991 FS
No sound and bad image 1k resistor on the abl line Obs I already got this resistor open and replaced fabiusmax
CCE HPS 1471
Retrace lines when turning on the TV Fr901 starting on the tube plate, made the change and resolved HardNet
CCE HPS 1741
Retrace lines Hello colleagues, I finally found the problem with the closed vertical line, as tsound is an R316 SMD responsible for the voltage on the vertical IC which is close to the vertical IC, I think I accidentally removed it with the soldering iron tip. Even the vertical IC problem was resolved. thanks for everyone's help. HardNet