Cce Repair Tips
Search: cce
Results: 4824
Results: 4824
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
HPS-1401H
|
TV turning on with screen washed like fog with sound!!!! | When checking the vertical area, contact resistor 1 r fr402 of -12 was burnt and the vertical was shorted. | I replaced the vertical and the resistor and that's it, the TV was ready | heliomar |
| CCE |
2918USP/AV
|
Vertical closed in half, from the middle to the top of the screen. | N 301 ( stv - 8172a) partial short | Replace the same. | BARRETO CRUZ |
| CCE |
2918USP/AV
|
LED lights up, blinks 3 times, and does not turn on. | R - 423(10r) e vd 421 | Replace the same | BARRETO CRUZ |
| CCE |
2918USP/AV
|
Replace the same. | N 701 ( bl 24c08 ) | Replace the same. | BARRETO CRUZ |
| CCE |
TV2118USP
|
Then it turns on, it turns off and goes into low power supply protection, horizontal with just 100v, if it keeps insisting the flyback heats up along with the horizontal, note: the c417 was replaced, which was charred. | After checking the entire board (capacitors, transistors and resistors) tsound was only one missing! the flyback bsc25-0224k- was altered, replaced and everything works fine. | Flyback replacement (bsc25-0224k) and everything functional cool. | João - Palmares |
| CCE |
TV2118USP
|
Reduced image as if it were the deflector | Q406 leaking. | Replace q406 = 2sd2060 | JHONNES. |
| CCE |
HPS1479
|
Increasing volume alone | Key 2 c772 1n smd | Fernando R. | |
| CCE |
HPS1471
|
Increasing the volume alone | Key 1 c771 1n smd | Fernando R. | |
| CCE |
HPS 1471
|
Dark stripe on the side | C 425 / 47/160v seco | Flad 8 # 23/08 12 | |
| CCE |
HPS-1403
|
Dark images but when enlarged and lowered the screen gives a yellowish, almost green image with a black vertical bar on the left side | Change the 27k resistor 404 and measure from pin 41 of ic 501 tda 8841-2y to r-404- and from 404 to pin 24 of the processor ic 701=mc68hco5cc1 controller and check the complete track on the part of the white paint on the side next to the r-g-b output connector in my case it was a broken track under the white paint next to the r-g-b output connector - it was so perfect... |
JUVELINO | |
| CCE |
HPS2992FS
|
+ b horizontal above the value does not generate low power supplys of choper traffic | Trail departure pin 8 trafo chopper | Track rework | luiz2012 |
| CCE |
HPS2991 FS
|
Led power off wk +b not secondary | C816 sold out | ||
| CCE |
HPS2985
|
Retrace lines, washed screen (white) does not operate controls (buttons) and no sound from channels, inhibits (sda & scl) | R901(22r), does not power (rgb) & inhibits (sda and scl) | Alextecnico | |
| CCE |
TV2118USP
TV2118 |
With the image jagged and warping??? | C-417 I changed it and it was ok....blzzz | C-417 | neupsx4download |
| CCE |
HPS 1497
|
The LED turns off and it doesn't turn on (it oscillates) | Ver for 402 | Master Eletronica | |
| CCE |
HPS-3407B
|
Burning ic 301 ( tda8359j ) and fr423 | Replace q802 and q805 of bc337 for bd135 without measuring. put another tda and another fr423 | paulorusso | |
| CCE |
HPS 1470
|
Ñ league. | Q 402(bu2527dx) | Replace the same | BARRETO CRUZ |
| CCE |
HPS2198
KK |
Turns on with LED flashing without video crown opening the case turns red | Q909 | Q909 | fernado tj maçeio |
| CCE |
HPS-2907FS=HPS-3407FS
|
It doesn't turn on, the filament lights up and tsound is no image hitting the tube plate, it turns on normally @@@ | In my case, I solved all the solder bridges on the PCI PLA tube, the defect was resolved. | Help yourself leave your tip | ELETRONICA ARNI-SC /L.LEAL |
| CCE |
HPS 2171
|
Does not turn on LED blinks | Power supplys do not stabilize capacitor c824 | Domingos da Eletronica |