Cce Repair Tips
Search: cce
Results: 4816
Results: 4816
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE - DISNEY |
HDC142 FS
|
Doesn't start | Low supply, activating eht protection, disconnecting pin 34 of the microela works, dz401 changed, measuring is good, however the voltage at its terminals is high, causing the protection to fail, tsound is no point in measuring analogically, changing directly. | ||
| CCE |
HPS-2171-FSH
|
Completely stopped, not even the LED lights up. | Change the capacity. electrolytic power supply. (150mf 400v) dry. | elet.washington | |
| CCE |
HPS-1407
|
TV stopped with all normal power supplys (when you turn on the power, the LED blinks indefinitely. | C-825 - 47/160 (disabled) | Just replace it and go for the hug....... thanks everyone for the tips (god bless you) | |
| TVCCE |
HPS2991FS
|
When turned on, the image takes a while to appear or no image appears at all. | +b normal, filament lights up normally, has high, normal screen and normal power supply. | Q-905 with cold welding on the tube plate. | Adilson(formiga-mg)-email= |
| CCE |
HPS2981C
|
TV stopped doesn't turn on. | Due to poor contact on the horizontal deflector coil socket pin, pin referring to the horizontal circuit. Due to this poor contact, the horizontal output tr was shorted and after changing it, the TV worked with a normal image, but without sound. I then discovered that the ,q 602=bc547b was shorted in the sound output pre. | The horizontal output tr and the q602 =bc547b sound pre were replaced and it looks great. | Armando de olímpia Eletronica EvoluSom |
| CCE |
HPS2097
-------- |
A black band on the left and right side of + - 2cm in the vertical direction, and immediately turning off.power supply+b with 97v. the right one is 102v. | C825 low cut | Replace c825 de 47mf p/ 160v | Ademir tc |
| CCE |
HPS-2997FS
|
Dark screen (no weave) | C409(394j/250volt)poliester | Replace it without testing | Jarbas (ELETRO-SERV) |
| CCE / CYBER VISION |
HSP2991 / TP-2958
HSP2991 |
When pressing the "on" key, the TV turns on but does not accept commands from the control and the screen remains off. | When activating the service menu function 02 (vsd), the controller causes the standby system to malfunction. | Place a switch between pin 78 of the TDA (central processor) and the board's ground. When pressing the on button, immediately after holding down this previously soldered service button for 30 seconds, after releasing it the TV will turn on. Press the service button twice again and the TV will enter service mode, then enter 96 and replace the option to "02". press osd/out to exit and that's it! | Paparotti |
| CCE |
HPS2197
|
Turn on turn off | C825 47uf 160v with leakage | Replace of the same | orlando lott |
| CCE |
2118USP/AV
|
Burning of the horizontal output transistor | Capacitor position 419 defective and just replace directly without measuring | ||
| CCE |
HPS2181
|
Going out of tune | T103 | 4.7pf mini tubular capacitor inside the damaged t103 coil, break it and place a 4.7pf ceramic capacitor. under the plate | FERNANDO ALCANTRA DE OLIVEIRA |
| CCE |
HPS2071
34BI |
Turns on when cold and then turns off after a few minutes. When it heats up and the stand-by LED flashes | Fr401 (1Ω) damaged or cold soldered, located in the horizontal deflection circuit | Replace fr401 or re-weld | TECNOGUEDES |
| CCE |
HPS - 2071 FSG
34BI |
Turns on, the image appears and disappears as quickly as a blinker. | Replace capacitor 825 (47uf/160v.) | BARRETO CRUZ | |
| CCE |
HPS 2004
|
The TV turns on the LED, you try to turn it on, the LED turns off but the TV doesn't turn on. | Q803=bc337 with the base and collector open. | It was replaced and resolved. | Armando da Eletronica EvoluSom,Olimpia. |
| CCE |
HPS 2997FS
|
Burning abl line resistors | Shorted flyback | paulorusso | |
| CCE |
HPS-2185FS HPS-2171FS
|
Power supply inoperative nor the standby LED lights up after a while it turns on normally @@@ | Ic 801 (tea1533at) da power supply | ELETRONICA ARNI-L. LEAL- SC | |
| CCE |
HPS-2071 E 1471
|
Normal power supply has all voltages 103v and 16v @@@ | Cristal do micro x701 | ELETRONICA ARNI-L. LEAL- SC | |
| CCE |
HPS1471
|
It turns on immediately after the image appears, a black band appears horizontally and interferes with the blue screen and intermittently turns off normal power supplys | C-417 with fault measuring it is good to change without measuring. | Capacitor replaced. | play back |
| CCE |
TV 2918 USP
|
Image shaking and closing on the sides | C 402 | Wanderlei | |
| CCE |
HPS2981C
|
5v power supply does not work with 3v | C825 as low capacitance | PEDRO EUGÊNIO |